REMOVAL
Removal / installation · Vehicles built Jul 2007 – Oct 2010
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012
- HINT:
- Use the same procedure for both the RH and LH sides.
- The procedure described below is for the LH side.
| 1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
|
| 2.
REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH
|
 |
- Pull the rear seatback lock release button and tilt the rear seatback forward.
Disengage the 10 clips and remove the rear seatback board carpet.
| 3.
REMOVE REAR SEATBACK ASSEMBLY RH
|
 |
- Pull up the rear seatback.
Remove the bolt and the anchor plate of the rear center seat outer belt.
- Remove the rear seat inner belt from the rear seatback holder.
Pull the rear seatback lock release button and tilt the rear seatback forward.
Remove the 2 bolts.
Disengage the hook and remove the rear seatback.
| 4.
REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH
|
 |
- Pull the rear seatback lock release button and tilt the rear seatback forward.
Disengage the 8 clips and remove the rear seatback board carpet.
| 5.
REMOVE REAR SEATBACK ASSEMBLY LH
|
 |
- Remove the rear center seat inner belt from the rear seatback holder.
Remove the 2 bolts.
Disengage the hook and remove the rear seatback.
| 6.
REMOVE REAR FLOOR BOARD
|
 |
- Remove the bolt and the luggage hold belt striker.
- HINT:
- Use the same procedure for both sides.
- Disengage the clip and the claw and remove the rear floor board.
| 7.
REMOVE REAR FLOOR MAT SUPPORT PLATE
|
 |
- Remove the 5 screws.
- Disengage the 11 claws and remove the rear floor mat support plate.
| 8.
REMOVE REAR FLOOR MAT ASSEMBLY
|
 |
- Using a clip remover, remove the 2 clips and the rear floor mat.
| 9.
REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY
|
 |
- HINT:
- Use the same procedure for both sides.
- Remove the cap.
Remove the bolt and the luggage hold belt striker.
| 10.
REMOVE FRONT DOOR SCUFF PLATE RH
|
 |
- Disengage the 14 claws and remove the front door scuff plate.
| 11.
REMOVE FRONT DOOR SCUFF PLATE LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 12.
REMOVE REAR DOOR SCUFF PLATE RH
|
 |
- Disengage the 6 claws and remove the access door scuff plate.
| 13.
REMOVE REAR DOOR SCUFF PLATE LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 14.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
|
 |
- Remove the front door opening trim weatherstrip.
| 15.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 16.
REMOVE DECK SIDE GARNISH (w/ Woofer)
|
 |
- Disengage the 6 claws and remove the rear deck side garnish.
| 17.
REMOVE SPEAKER MOUNTING COVER (w/ Woofer)
|
 |
- Disengage the 8 clips and remove the speaker mounting cover.
| 18.
REMOVE AMPLIFIER BOX SPEAKER ASSEMBLY (w/ Woofer)
|
 |
- Disconnect the speaker connector.
Remove the 4 screws and the amplifier box speaker.
| 19.
REMOVE PACKAGE HOLDER NET HOOK
|
 |
- HINT:
- Use the same procedure to remove all the package holder net hooks.
Remove the screw and the package holder net hook.
| 20.
REMOVE QUARTER TRIM POCKET TRAY (w/o Woofer)
|
 |
- Disengage the 7 claws and remove the quarter trim pocket tray.
| 21.
REMOVE SIDE TRIM COVER (w/o Woofer)
|
 |
- Disengage the 8 claws and remove the side trim cover.
| 22.
REMOVE QUARTER TRIM POCKET (w/o Woofer)
|
 |
- Disengage the 6 claws and remove the quarter trim pocket.
| 23.
REMOVE LAP BELT OUTER ANCHOR COVER
|
 |
- HINT:
- Use the same procedure for both sides.
Disengage the 3 claws and remove the lap belt outer anchor cover.
| 24.
REMOVE REAR SEAT OUTER BELT ASSEMBLY RH
|
 |
- Remove the bolt and the anchor plate.
| 25.
REMOVE REAR SEAT OUTER BELT ASSEMBLY LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 26.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
|
 |
- Remove the 4 screws.
- Disengage the 6 clips and the 8 claws and remove the deck trim side panel.
| 27.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
|
 |
- Remove the 3 screws.
- Disengage the 6 clips and the 8 claws and remove the deck trim side panel.
| 28.
REMOVE ROOF SIDE INNER GARNISH RH
|
 |
- Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
- Remove the bolt and the clip.
Disengage the 7 clips and the claw and remove the roof side inner garnish.
Pass the rear seat outer belt through the slit in the roof side inner garnish.
| 29.
REMOVE ROOF SIDE INNER GARNISH LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 30.
REMOVE QUARTER WINDOW GLASS |
 |
Apply protective tape to the outer circumference of the quarter window, as shown in the illustration.
From the interior, insert piano wires between the vehicle body and quarter window, as shown in the illustration.
Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.
- NOTICE:
- When separating the quarter window from the vehicle, do not damage the vehicle's paintwork or exterior/interior ornaments.
Cut through the adhesive by pulling the piano wire around the quarter window.