2011-2016 FJ Cruiser · Service Manual ENGINE

P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built from Aug 2009

Also covers:

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009

DESCRIPTION

A flat type knock sensor (non-resonant type) has a structure that can detect vibrations over a wide band of frequencies: between approximately 5 kHz and 15 kHz.
Knock sensors are fitted onto the engine block to detect engine knocking.
The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.
DTC No.
DTC Detection Condition
Trouble Area
P0327
P0332
Output voltage of knock sensor less than 0.5 V for 1 second
(1 trip detection logic)
  1. Short in knock sensor circuit
  2. Knock sensor
  3. ECM
P0328
P0333
Output voltage of knock sensor more than 4.5 V for 1 second
(1 trip detection logic)
  1. Open in knock sensor circuit
  2. Knock sensor
  3. ECM

HINT:
When any of DTCs P0327, P0328, P0332 and P0333 are set, the ECM enters fail-safe mode. During fail- safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.


  1. A085286E73
  2. Inspection using an oscilloscope
    The correct waveform is as shown.
    Item
    Content
    Terminal
    KNK1 - EKNK
    or
    KNK2 - EKN2
    Equipment Setting
    0.01 to 10 V/DIV,
    0.01 to 10 msec./DIV,
    Condition
    Keep engine speed at 4000 rpm with
    warm engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low or high for 1 second, the ECM interprets this as a malfunction in the sensor circuit, and sets a DTC.
The monitor for DTCs P0327 and P0328 begins to run when 5 seconds have elapsed since the engine was started.
If the malfunction is not repaired successfully, any of DTC P0327, P0328, P0332 or P0333 is set 5 seconds after the engine is next started.

WIRING DIAGRAM

A193261E02

INSPECTION PROCEDURE

HINT:
  1. DTCs P0327 and P0328 are for the bank 1 knock sensor circuit.
  1. DTCs P0332 and P0333 are for the bank 2 knock sensor circuit.
  1. Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ OUTPUT DTC (CHECK KNOCK SENSOR CIRCUIT)
A224009E01
  1. Disconnect the BU1 connector.

  1. Using lead wires, connect the connectors as follows.

    Male Connector - Female Connector
    Terminal 2 - Terminal 4
    Terminal 5 - Terminal 6
    Terminal 4 - Terminal 2
    Terminal 6 - Terminal 5

  1. Warm up the engine.

  1. Run the engine at 3000 rpm for 10 seconds or more.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTCs same as when vehicle brought in
    P0327, P0328 → P0327, P0328
    or
    P0332, P0333 → P0332, P0333
    A
    DTCs different from when vehicle brought in
    P0327, P0328 → P0332, P0333
    or
    P0332, P0333 → P0327, P0328
    B
    Text in Illustration 
    *1
    Knock Sensor
    *2
    Male Connector
    *3
    Female Connector



B
Go to step 4
A


2. CHECK HARNESS AND CONNECTOR (CONNECTOR - ECM)
A226858E01
  1. Disconnect the BU1 connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    2 (BU1 female connector) - B48-11 (KNK1)
    Always
    Below 1 Ω
    5 (BU1 female connector) - B48-12 (EKNK)
    Always
    Below 1 Ω
    4 (BU1 female connector) - B48-5 (KNK2)
    Always
    Below 1 Ω
    6 (BU1 female connector) - B48-6 (EKN2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    2 (BU1 female connector) or B48-11 (KNK1) - Body ground
    Always
    10 kΩ or higher
    5 (BU1 female connector) or B48-12 (EKNK) - Body ground
    Always
    10 kΩ or higher
    4 (BU1 female connector) or B48-5 (KNK2) - Body ground
    Always
    10 kΩ or higher
    6 (BU1 female connector) or B48-6 (EKN2) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)
    *2
    Rear view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM
A226859E02
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B48-11 (KNK1) - B48-12 (EKNK)
    Ignition switch ON
    4.5 to 5.5 V
    B48-5 (KNK2) - B48-6 (EKN2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to ECM)



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

4. INSPECT KNOCK SENSOR
A072922E30
  1. Disconnect the BU1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - 5
    20°C (68°F)
    120 to 280 kΩ
    4 - 6
    20°C (68°F)
    120 to 280 kΩ

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Knock Sensor)



NG
Go to step 5
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

5. CHECK HARNESS AND CONNECTOR (CONNECTOR - KNOCK SENSOR)

HINT:
  1. If DTC P0327 or P0328 has changed to P0332 or P0333, check the knock sensor circuit on the right bank side.
  1. If DTC P0332 or P0333 has changed to P0327 or P0328, check the knock sensor circuit on the left bank side.

  1. Disconnect the BU1 connector.

  1. Disconnect the knock sensor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    2 (BU1 male connector) - U2-2
    Always
    Below 1 Ω
    5 (BU1 male connector) - U2-1
    Always
    Below 1 Ω
    4 (BU1 male connector) - U1-2
    Always
    Below 1 Ω
    6 (BU1 male connector) - U1-1
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    2 (BU1 male connector) or U2-2 - Body ground
    Always
    10 kΩ or higher
    5 (BU1 male connector) or U2-1 - Body ground
    Always
    10 kΩ or higher
    4 (BU1 male connector) or U1-2 - Body ground
    Always
    10 kΩ or higher
    6 (BU1 male connector) or U1-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE KNOCK SENSOR


← P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) (+ P0328, P0332, P0333) (Jul 2007 – Jul 2009)P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (Jul 2007 – Jul 2009) →