2011-2016 FJ Cruiser · Service Manual ENGINE

P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Also covers:

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009

DESCRIPTION

A flat type knock sensor (non-resonant type) has a structure that can detect vibrations over a wide band of frequencies: between approximately 6 kHz and 15 kHz.
Knock sensors are fitted onto the engine block to detect engine knocking.
The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.
DTC No.
DTC Detection Conditions
Trouble Areas
P0327
P0332
Output voltage of knock sensor 1 or 2 is 0.5 V or less (1 trip detection logic)
  1. Short in knock sensor 1 or 2 circuit
  2. Knock sensor 1 or 2
  3. ECM
P0328
P0333
Output voltage of knock sensor 1 or 2 is 4.5 V or more (1 trip detection logic)
  1. Open in knock sensor 1 or 2 circuit
  2. Knock sensor 1 or 2
  3. ECM

HINT:
When any of DTCs P0327, P0328, P0332 and P0333 are set, the ECM enters fail-safe mode. During fail- safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned OFF.


  1. A085286E53
  2. Reference: Inspection using an oscilloscope
    The correct waveform is as shown.
    Items
    Contents
    Terminals
    KNK1 - EKNK
    or
    KNK2 - EKN2
    Equipment Settings
    1 V/DIV,
    1 msec./DIV
    Conditions
    Keep engine speed at 4,000 rpm with
    warm engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low or high for more than 1 second, the ECM interprets this as a malfunction in the sensor circuit, and sets a DTC.
The monitor for DTCs P0327, P0328, P0332 and P0333 begins to run when 5 seconds have elapsed since the engine was started.
If the malfunction is not repaired successfully, any of DTC P0327, P0328, P0332 or P0333 is set 5 seconds after the engine is next started.

WIRING DIAGRAM

A133416E02

INSPECTION PROCEDURE

HINT:
  1. DTCs P0327 and P0328 are for the bank 1 knock sensor circuit.
  1. DTCs P0332 and P0333 are for the bank 2 knock sensor circuit.
  1. Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ OUTPUT DTC (CHECK KNOCK SENSOR CIRCUIT)
A073822E20
  1. Disconnect the BU1 connector.

  1. Using lead wires, connect the connectors as follows.

    Male Connector - Female Connector
    Terminal 2 - Terminal 4
    Terminal 5 - Terminal 6
    Terminal 4 - Terminal 2
    Terminal 6 - Terminal 5

  1. Warm up the engine.

  1. Run the engine at 3,000 rpm for 10 seconds or more.

  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the item: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display
    Proceed To
    DTCs same as when vehicle brought in
    P0327, P0328 → P0327, P0328
    or
    P0332, P0333 → P0332, P0333
    A
    DTCs different from when vehicle brought in
    P0327, P0328 → P0332, P0333
    or
    P0332, P0333 → P0327, P0328
    B

  1. Reconnect the BU1 connector.



B
Go to step 4
A


2. CHECK HARNESS AND CONNECTOR (CONNECTOR - ECM)
A116288E05
  1. Disconnect the BU1 connector.

  1. Disconnect the B2 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    BU1 female connector 2 - KNK1 (B2-29)
    Below 1 Ω
    BU1 female connector 5 - EKNK (B2-28)
    BU1 female connector 4 - KNK2 (B2-21)
    BU1 female connector 6 - EKN2 (B2-20)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    BU1 female connector 2 or KNK1 (B2-29) - Body ground
    10 kΩ or higher
    BU1 female connector 5 or EKNK (B2-28) - Body ground
    BU1 female connector 4 or KNK2 (B2-21) - Body ground
    BU1 female connector 6 or EKN2 (B2-20) - Body ground

  1. Reconnect the BU1 connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM
G035655E15
  1. Disconnect the B2 ECM connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage between the ECM terminals.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    KNK1 (B2-29) - EKNK (B2-28)
    4.5 to 5.5 V
    KNK2 (B2-21) - EKN2 (B2-20)

  1. Reconnect the ECM connector.



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

4. INSPECT KNOCK SENSOR
A072922E15
  1. Disconnect the BU1 connector.

  1. Check the resistance between the terminals of the BU1 male connector.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    BU1 male connector 2 - 5
    120 to 280 kΩ
    BU1 male connector 4 - 6

  1. Reconnect the BU1 connector.



OK
CHECK FOR INTERMITTENT PROBLEMS (Click here)
NG


5. CHECK HARNESS AND CONNECTOR (CONNECTOR - KNOCK SENSOR)
A116289E03

HINT:
  1. If DTC P0327 or P0328 has changed to P0332 or P0333, check the knock sensor circuit on the right bank side.
  1. If DTC P0332 or P0333 has changed to P0327 or P0328, check the knock sensor circuit on the left bank side.

  1. Disconnect the BU1 connector.

  1. Disconnect the U1 and U2 knock sensor connectors.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    BU1 male connector 2 - U2-2
    Below 1 Ω
    BU1 male connector 5 - U2-1
    BU1 male connector 4 - U1-2
    BU1 male connector 6 - U1-1

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    BU1 male connector 2 or U2-2 - Body ground
    10 kΩ or higher
    BU1 male connector 5 or U2-1 - Body ground
    BU1 male connector 4 or U1-2 - Body ground
    BU1 male connector 6 or U1-1 - Body ground

  1. Reconnect the BU1 connector.

  1. Reconnect the knock sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE KNOCK SENSOR (Click here)


← P0300 Random / Multiple Cylinder Misfire Detected (+ 6 more codes) (from Aug 2014)P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) (+ P0328, P0332, P0333) (from Aug 2009) →