2011-2016 FJ Cruiser · Service Manual ENGINE

REPLACEMENT

Removal / installation · Vehicles built from Aug 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


1. REPLACE INTAKE VALVE GUIDE BUSH
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A222129E01
    Using SST and a hammer, tap out the intake valve guide bushes.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

  1. Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head.

    Standard Bush Bore Diameter:
    Item
    Specified Condition
    STD
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)
    O/S 0.05
    10.335 to 10.356 mm (0.4069 to 0.4077 in.)

  1. Select a new valve guide bush.

    Select a New Guide Bush:
    Item
    Specified Condition
    Bush bore diameter
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)
    10.335 to 10.356 mm (0.4069 to 0.4077 in.)
    Use bush
    STD
    O/S 0.05

    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore diameter to 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.
    If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.

    New Guide Bush Diameter:
    Item
    Specified Condition
    STD
    10.333 to 10.344 mm (0.4068 to 0.4072 in.)
    O/S 0.05
    10.383 to 10.394 mm (0.4088 to 0.4092 in.)

    HINT:
    Different bushes are used for the intake and exhaust.

    Standard bush length:
    41.3 to 41.7 mm (1.63 to 1.64 in.)

  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A221110E02
    Using SST, tap in the intake valve guide bushes to the specified protrusion height.
    Text in Illustration 
    *a
    Protrusion Height
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Protrusion height:
    9.10 to 9.90 mm (0.358 to 0.390 in.)

  1. A131839
    Using a sharp 5.5 mm reamer, ream the valve guide bushings to obtain the specified clearance.

    Standard oil clearance:
    0.025 to 0.060 mm (0.000984 to 0.00236 in.)


2. REPLACE EXHAUST VALVE GUIDE BUSH
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A222130E01
    Using SST and a hammer, tap out the exhaust valve guide bushes.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

  1. Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head.

    Standard Bush Bore Diameter:
    Item
    Specified Condition
    STD
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)
    O/S 0.05
    10.335 to 10.356 mm (0.4069 to 0.4077 in.)

  1. Select a new valve guide bush.

    Select a New Guide Bush:
    Item
    Specified Condition
    Bush bore diameter
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)
    10.335 to 10.356 mm (0.4069 to 0.4077 in.)
    Use bush
    STD
    O/S 0.05

    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.
    If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.

    New Guide Bush Diameter:
    Item
    Specified Condition
    STD
    10.333 to 10.344 mm (0.4068 to 0.4072 in.)
    O/S 0.05
    10.383 to 10.394 mm (0.4088 to 0.4092 in.)

    HINT:
    Different bushes are used for the intake and exhaust.

    Standard bush length:
    46.8 to 47.2 mm (1.84 to 1.86 in.)

  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A221111E02
    Using SST, tap in the exhaust valve guide bushes to the specified protrusion height.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Protrusion height:
    9.10 to 9.90 mm (0.358 to 0.390 in.)

    Text in Illustration 
    *a
    Protrusion Height

  1. A096429
    Using a sharp 5.5 mm reamer, ream the valve guide bushings to obtain the specified clearance.

    Standard oil clearance:
    0.030 to 0.065 mm (0.00118 to 0.00256 in.)


3. REPLACE UNION

  1. Remove the union from the bank 1 cylinder head (front side) and bank 2 cylinder head (intake port side).

    A222133E02

    Text in Illustration 
    *a
    Front Side of RH:
    *b
    Intake Side of LH:

  1. Apply adhesive to 2 or 3 threads of the bolt ends of new unions.

    Adhesive:
    Toyota Genuine Seal Adhesive 1324, Three Bond 1324 or equivalent

  1. Using a 12 mm deep socket wrench, install the 2 unions.

    Torque:
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }


4. REPLACE TIGHT PLUG

HINT:
If coolant leaks from a tight plug or a plug is corroded, replace it.

  1. Remove the tight plugs.

  1. Apply adhesive around new tight plugs.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using SST and a hammer, tap in the tight plugs to the standard depth.

    A222132E02

    Text in Illustration 
    *a
    RH:
    *b
    LH:
    *c
    Standard depth
    -
    -
    SST
    09950-60010   (09951-00250)
    09950-70010   (09951-07150)

    Standard depth:
    1.7 to 2.7 mm (0.0669 to 0.106 in.)


5. REPLACE STRAIGHT PIN

HINT:
If a straight pin is deformed, replace it.

  1. Using a plastic-faced hammer, tap in new straight pins as shown in the illustration.

    A221114E02

    Text in Illustration 
    *a
    RH:
    *b
    LH:
    *c
    Protrusion height
    -
    -

    Protrusion height:
    18.0 to 19.0 mm (0.708 to 0.748 in.)


6. REPLACE RING PIN

HINT:
It is not necessary to remove a ring pin unless it is being replaced.

  1. A221112E02
    Using a plastic-faced hammer, tap in new ring pins to the specified protrusion height.
    Text in Illustration 
    *a
    RH:
    *b
    LH:
    *c
    Protrusion Height

    Protrusion height:
    2.5 to 3.5 mm (0.0984 to 0.138 in.)


7. REPLACE SPARK PLUG TUBE

A223702E02

HINT:
When using a new cylinder head, the spark plug tubes must be replaced.

  1. Remove the spark plug tube.

    Text in Illustration 
    *1
    Adhesive
    *a
    Distance

  1. Apply adhesive to the end of a new spark plug tube.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

    Standard seal diameter:
    1.0 to 3.0 mm (0.394 to 0.118 in.)

    Distance:
    9.0 to 15.0 mm (0.354 to 0.590 in.)

    NOTICE:
    1. Be careful not to deform the spark plug tube.
    2. Be careful not to expose the seal to coolant for at least 1 hour after installing it.

  1. A223701E02
    Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.
    Text in Illustration 
    *a
    Cylinder Head Top Surface
    *b
    Protrusion Height

    Standard protrusion height:
    75.1 to 76.1 mm (2.96 to 3.00 in.)

    NOTICE:
    To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.

← REPLACEMENT (Jul 2007 – Jul 2009)REASSEMBLY (Jul 2007 – Jul 2009) →