2011-2016 FJ Cruiser · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Aug 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


1. INSTALL STUD BOLT

HINT:
If a stud bolt is deformed or the threads are damaged, replace it.

  1. Using E6 and E8 "TORX" sockets, install the stud bolts.

    A222131E02

    Text in Illustration 
    *a
    Intake Side of RH:
    *b
    Intake Side of LH:
    *c
    Exhaust Side of RH:
    *d
    Exhaust Side of LH:
    *e
    Rear Side of RH:
    *f
    Rear Side of LH:

    Torque:
    for bolts A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }


2. INSTALL NO. 2 STRAIGHT SCREW PLUG
  1. Using a 14 mm hexagon wrench, install 2 new gaskets and the 2 No. 2 straight screw plugs.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }


3. INSTALL NO. 1 STRAIGHT SCREW PLUG
  1. Using a 10 mm hexagon wrench, install 4 new gaskets and the 4 No. 1 straight screw plugs.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


4. INSTALL VALVE SPRING SEAT
  1. Install the valve spring seats to the cylinder head.


5. INSTALL VALVE STEM OIL SEAL

A094934E13
  1. Apply a light coat of engine oil to new valve stem oil seals.

    Text in Illustration 
    *a
    Intake Side
    *b
    Exhaust Side
    *c
    Gray
    *d
    Black

    HINT:
    The intake valve oil seals are gray and the exhaust valve oil seals are black.

    NOTICE:
    Pay attention when installing the intake and exhaust valve stem oil seals. For example, installing the intake valve stem oil seal to the exhaust side or installing the exhaust valve stem oil seal to the intake side can cause installation problems later.

  1. A124592E04
    Using SST, push in the oil seals.
    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT
    SST
    09201-41020  

    NOTICE:
    Failure to use SST will cause the seal to be damaged or improperly seated.


6. INSTALL INTAKE VALVE

  1. A094935E22
    Apply a sufficient coat of engine oil to the tip area of the intake valve shown in the illustration.
    Text in Illustration 
    *a
    30 mm (1.18 in.) or more

  1. Install the intake valve, inner compression spring and valve spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to their original locations.

  1. Using SST, compress the inner compression spring and install the 2 valve spring retainer locks.

    SST
    09202-70020   (09202-00010)

  1. A221116
    Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the retainer.


7. INSTALL EXHAUST VALVE

  1. A094936E21
    Apply a sufficient coat of engine oil to the tip area of the exhaust valve shown in the illustration.
    Text in Illustration 
    *a
    30 mm (1.18 in.) or more

  1. Install the exhaust valve, inner compression spring and valve spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to the original locations.

  1. Using SST, compress the inner compression spring and install the 2 valve spring retainer locks.

    SST
    09202-70020   (09202-00010)

  1. A221115
    Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the retainer.

← REASSEMBLY (Jul 2007 – Jul 2009)INSTALLATION (Jul 2007 – Jul 2009) →