2011-2016 FJ Cruiser · Service Manual ENGINE

P0560 System Voltage

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009

DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is in the OFF position. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, these memories are cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and sets the DTC.
DTC No.
DTC Detection Conditions
Trouble Areas
P0560
Open in ECM back up power source circuit (1 trip detection logic)
  1. Open in back up power source circuit
  2. EFI fuse
  3. ECM

HINT:
If DTC P0560 is set, the ECM does not store other DTCs.


WIRING DIAGRAM

A133422E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK FUSE (EFI FUSE)
A133436E04
  1. Remove the EFI fuse from the engine room relay block.

  1. Check the EFI fuse resistance.

    Standard Resistance:
    Below 1 Ω

  1. Reinstall the EFI fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2. INSPECT ECM (BATT VOLTAGE)
G100798E11
  1. Measure the voltage between the terminals of the B3 and E47 ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    BATT (E47-3) - E1 (B3-1)
    11 to 14 V



NG
Go to step 3
OK

REPLACE ECM (Click here)

3. CHECK HARNESS AND CONNECTOR (ECM - EFI FUSE, EFI FUSE - BATTERY)
A133447E03
  1. Check the harness and the connector between the EFI fuse and ECM.

    1. Remove the EFI fuse from the engine room relay block.

    2. Disconnect the E47 ECM connector.

    3. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connections
      Specified Conditions
      EFI fuse (2) - BATT (E47-3)
      Below 1 Ω

      Standard Resistance (Check for short):
      Tester Connections
      Specified Conditions
      EFI fuse (2) or BATT (E47-3) - Body ground
      10 kΩ or higher

    4. Reconnect the ECM connector.

    5. Reinstall the EFI fuse.

  1. Check the harness and the connector between the EFI fuse and battery.

    1. Remove the EFI fuse from the engine room relay block.

    2. Disconnect the negative battery terminal.

    3. Disconnect the positive battery terminal.

    4. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connections
      Specified Conditions
      Battery positive terminal - EFI fuse (1)
      Below 1 Ω

      Standard Resistance (Check for short):
      Tester Connections
      Specified Conditions
      Battery positive terminal or EFI fuse (1) - Body ground
      10 kΩ or higher

    5. Reconnect the positive battery terminal.

    6. Reconnect the negative battery terminal.

    7. Reinstall the EFI fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery is not depleted.



NG
REPLACE BATTERY
OK

CHECK AND REPLACE ENGINE ROOM RELAY BLOCK


← P0550 Power Steering Pressure Sensor Circuit Malfunction (+ P0552, P0553) (from Aug 2009)P0560 System Voltage (from Aug 2009) →