2011-2016 FJ Cruiser · Service Manual ENGINE

P0102 Mass or Volume Air Flow Circuit Low Input

Diagnostic trouble codes · Vehicles built from Aug 2009

Also covers:

DESCRIPTION

The Mass Air Flow (MAF) meter is a sensor that measures the amount of air flowing through the throttle valve.
The ECM uses this information to determine the fuel injection time and to provide appropriate air-fuel ratio.
Inside the MAF meter, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the MAF meter. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor provide a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:
When any of these DTCs are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine RPM and throttle valve position. Fail-safe mode continues until a pass condition is detected.

A202104E05
DTC No.
DTC Detection Condition
Trouble Area
P0102
Mass Air Flow (MAF) meter voltage less than 0.2 V for 3 seconds
(1 trip detection logic)
  1. Open or short in MAF meter circuit
  2. MAF meter
  3. ECM
P0103
Mass Air Flow (MAF) meter voltage more than 4.9 V for 3 seconds
(1 trip detection logic)
  1. Open or short in MAF meter circuit
  2. MAF meter
  3. ECM

HINT:
When any of these DTCs are set, check the air-flow rate by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / All Data / MAF.
Mass Air Flow Rate (gm/sec)
Malfunction
Approximately 0.0
  1. Open in Mass Air Flow (MAF) meter power source circuit
  2. Open or short in VG circuit
271.0 or more
  1. Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect in the MAF meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the MAF meter and sets a DTC.
  1. Example:
    When the sensor voltage output remains less than 0.2 V, or more than 4.9 V, for more than 3 seconds, the ECM sets a DTC.
    If the malfunction is not repaired successfully, a DTC is set 3 seconds after the engine is next started.

WIRING DIAGRAM

A193219E03

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE)
  1. Read the values using the intelligent tester (MAF).

    NOTICE:
    1. Turn the ignition switch off.
    2. Perform the inspection with the vehicle indoors and on a level surface.
    3. Perform the inspection of the mass air flow meter while it is installed in the air cleaner case (installed on the vehicle).
    4. During the test, do not use the exhaust air duct to perform suction on the exhaust pipe.

  1. Connect the tester to the DLC3.

  1. Turn the ignition switch to ON (do not start the engine).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

  1. Wait for 30 seconds, and read the values on the intelligent tester.

    Result 
    Result (gm/sec.)
    Proceed to
    0.0
    A
    0.92 or more
    B
    Between 0.0 and 0.92
    C



B
Go to step 5

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
A107942E29
  1. Disconnect the Mass Air Flow (MAF) meter connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B51-3 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Mass Air Flow Meter)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - EFI RELAY)
OK


3. INSPECT ECM (VG VOLTAGE)
A226857E06
  1. Start the engine.

  1. Measure the voltage between the terminals of the ECM connector.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B48-14 (VG) - B48-13 (E2G)
    Engine idling
    0.5 to 3.0 V

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to ECM)



NG
Go to step 4
OK

REPLACE ECM (Click here)

4. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the MAF meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B51-5 (VG) - B48-14 (VG)
    Always
    Below 1 Ω
    B51-4 (E2G) - B48-13 (E2G)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B51-5 (VG) or B48-14 (VG) - Body ground
    Always
    10 kΩ or higher
    B51-4 (E2G) or B48-13 (E2G) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER (Click here)

5. INSPECT ECM (SENSOR GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B48-13 (E2G) - Body ground
    Always
    Below 1 Ω



NG
REPLACE ECM (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the MAF meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B51-4 (E2G) - B48-13 (E2G)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B51-4 (E2G) or B48-13 (E2G) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER (Click here)


← P0100 Mass or Volume Air Flow Circuit (+ P0102, P0103) (Dec 2007 – Jul 2009)P0110 Intake Air Temperature Circuit (+ P0112, P0113) (Jul 2007 – Jul 2009) →