2011-2016 FJ Cruiser · Service Manual ENGINE

P0100 Mass or Volume Air Flow Circuit

Diagnostic trouble codes · Vehicles built Dec 2007 – Jul 2009

Also covers:

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009

DESCRIPTION

The Mass Air Flow (MAF) meter is a sensor that measures the amount of air flowing through the throttle valve.
The ECM uses this information to determine the fuel injection time and to provide appropriate air fuel ratio.
Inside the MAF meter, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the MAF meter. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor provide a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:
When any of these DTCs are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine RPM and throttle valve position. Fail-safe mode continues until a pass condition is detected.

A122492E01
DTC No.
DTC Detection Conditions
Trouble Areas
P0100
Open or short in Mass Air Flow (MAF) meter circuit for 3 seconds when engine speed less than 4000 rpm
(1 trip detection logic)
  1. Open or short in MAF meter circuit
  2. MAF meter
  3. ECM
P0102
Open in Mass Air Flow (MAF) meter circuit for 3 seconds when engine speed less than 4000 rpm
(1 trip detection logic)
  1. Open in MAF meter circuit
  2. Short in ground circuit
  3. MAF meter
  4. ECM
P0103
Short in Mass Air Flow (MAF) meter circuit for 3 seconds when engine speed less than 4000 rpm
(1 trip detection logic)
  1. Short in MAF meter circuit (+B circuit)
  2. MAF meter
  3. ECM

HINT:
When any of these DTCs are set, check the air-flow rate by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / MAF.
Mass Air Flow Rate (g/sec)
Malfunctions
Approximately 0.0
  1. Open in Mass Air Flow (MAF) meter power source circuit
  2. Open or short in VG circuit
271.0 or more
  1. Open in EVG circuit


MONITOR DESCRIPTION

If there is a defect in the MAF meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the MAF meter and sets a DTC.
Example:
When the sensor voltage output remains less than 0.2 V, or more than 4.9 V, for more than 3 seconds, the ECM sets a DTC.
If the malfunction is not repaired successfully, a DTC is set 3 seconds after the engine is next started.

WIRING DIAGRAM

A133457E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE)
  1. Connect an intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / MAF.

  1. Read the values displayed on the tester.

    Result:
    Mass Air Flow Rate (g/sec)
    Proceed To
    0.0
    A
    271.0 or more
    B
    Between 1.0 and 270.0 (*1)
    C

    *1: The value must be changed when the throttle valve is open or closed.



B
Go to step 6

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
A107942E07
  1. Disconnect the B13 Mass Air Flow (MAF) meter connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminal of the wire harness side connector and body ground.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    +B (B13-1) - Body ground
    11 to 14 V

  1. Reconnect the MAF meter connector.



NG
Go to step 5
OK


3. INSPECT ECM (VG VOLTAGE)
A115970E16
  1. Start the engine.

  1. Measure the voltage between the terminals of the B1 ECM connector.

    HINT:
    The transmission gear should be in the neutral and the A/C switch should be turned OFF.

    Standard Voltage:
    Tester Connections
    Conditions
    Specified Conditions
    VG (B1-30) - E2G (B1-29)
    Engine idling
    0.5 to 3.0 V



OK
REPLACE ECM (Click here)
NG


4. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A116158E03
  1. Disconnect the B13 MAF meter connector.

  1. Disconnect the B1 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    VG (B13-3) - VG (B1-30)
    Below 1 Ω
    E2G (B13-2) - E2G (B1-29)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    VG (B13-3) or VG (B1-30) - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER (Click here)

5. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - EFI RELAY)
A133474E04
  1. Inspect the EFI NO. 2 fuse.

    1. Remove the EFI NO. 2 fuse from the engine room relay block.

    2. Check the EFI NO. 2 fuse resistance.

      Standard Resistance:
      Below 1 Ω

    3. Reinstall the EFI NO. 2 fuse.

  1. Disconnect the B13 MAF meter connector.

  1. Remove the EFI relay from the engine room relay block.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    +B (B13-1) - EFI relay (3)
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    +B (B13-1) or EFI relay (3) - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reinstall the EFI relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)

6. INSPECT ECM (SENSOR GROUND)
A115970E17
  1. Check the resistance.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    E2G (B1-29) - Body ground
    Below 1 Ω



NG
REPLACE ECM (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A116158E04
  1. Disconnect the B13 MAF meter connector.

  1. Disconnect the B1 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    VG (B13-3) - VG (B1-30)
    Below 1 Ω
    E2G (B13-2) - E2G (B1-29)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    VG (B13-3) or VG (B1-30) - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER (Click here)


← P0100 Mass or Volume Air Flow Circuit (+ P0102, P0103) (Jul 2007 – Nov 2007)P0102 Mass or Volume Air Flow Circuit Low Input (+ P0103) (from Aug 2009) →