2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Key Lock-in Prevention Function does not Work Properly

Circuit diagnosis · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

When the key is in the ignition key cylinder or the door courtesy light ON signal is output to the main body ECU, performing the door lock operation with the lock switch does not lock the doors.

WIRING DIAGRAM

B138205E03

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (D DOOR COURTESY SW)
  1. Connect a intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on tester, read on the "Data List".


Main Body:
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door Courtesy SW
Driver side door courtesy switch signal / ON or OFF
ON: Driver side door is open
OFF: Driver side door is closed
-

OK:
The display is as specified in the normal condition.



NG
Go to step 5
OK


2. READ VALUE USING INTELLIGENT TESTER (KEY UNLOCK WARNING SW)
  1. Connect a intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on tester, read on the "Data List".


Main Body ECU:
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Key Unlock Warning SW
Unlock warning switch signal / ON or OFF
ON: Key is in ignition key cylinder
OFF: No key is in ignition key cylinder
-

OK:
The display is as specified in the normal condition.



NG
REPLACE MAIN BODY ECU
OK


3. INSPECT UNLOCK WARNING SWITCH

  1. B062710E01
    Remove the unlock warning switch.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Not pushed
    10 kΩor higher
    1 - 2
    Pushed
    Below 1 Ω



NG
REPLACE UNLOCK WARNING SWITCH (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU)

  1. B136070E02
    Disconnect the E21 unlock warning switch connector.

  1. Disconnect the E8 main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    E21-1 - E8-14 (KSW)
    Below 1 Ω
    E21-1 or E8-14 (KSW) - Body ground
    10 kΩor higher
    E21-2 - Body ground
    Below 1 Ω

  1. Reconnect the unlock warning switch connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

5. INSPECT FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE)

  1. E114552E01
    Remove the front door courtesy light switch (driver side).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Not pushed (ON)
    Below 1 Ω
    1 - Body ground
    Pushed (OFF)
    10 kΩor higher

  1. Reinstall the front door courtesy light switch (driver side).



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE) (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY SWITCH (DRIVER SIDE) - MAIN BODY ECU)

  1. B136069E01
    Disconnect the J1 front door courtesy light switch (driver side) connector.

  1. Disconnect the E7 main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    J1-1 - E7-23 (DCTY)
    Below 1 Ω
    J1-1 or E7-23 (DCTY) - Body ground
    10 kΩor higher

  1. Reconnect the front door courtesy light switch connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Only Back Door LOCK / UNLOCK Functions do not Operate (from Nov 2010)Key Lock-in Prevention Function does not Work Properly (from Nov 2010) →