2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Key Lock-in Prevention Function does not Work Properly

Circuit diagnosis · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

When the key is in the ignition key cylinder or the door courtesy light ON signal is output to the main body ECU, performing the door lock operation with the lock switch does not lock the doors.

WIRING DIAGRAM

B267288E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (D DOOR COURTESY SW)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Driver side door courtesy switch signal / ON or OFF
    ON: Driver side door is open
    OFF: Driver side door is closed
    -

OK:
The display is as specified in the normal condition.



NG
Go to step 3
OK


2. READ VALUE USING INTELLIGENT TESTER (KEY UNLOCK WARNING SW)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Unlock Warning SW
    Unlock warning switch signal / ON or OFF
    ON: Key is in ignition key cylinder
    OFF: No key is in ignition key cylinder
    -

OK:
The display is as specified in the normal condition.



NG
Go to step 5
OK

REPLACE MAIN BODY ECU

3. INSPECT FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE)
  1. Insect the front door courtesy light switch (driver side) (Click here).



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE) (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE))
  1. Disconnect the E7 main body ECU connector.

  1. for LHD

    1. Disconnect the J1 front door courtesy light switch (driver side) connector.

  1. for RHD

    1. Disconnect the I1 front door courtesy light switch (driver side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    E7-23 (DCTY) - J1-1
    Always
    Below 1 Ω
    E7-23 (DCTY) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    E7-23 (DCTY) - I1-1
    Always
    Below 1 Ω
    E7-23 (DCTY) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the front door courtesy light switch (driver side) connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

5. INSPECT UNLOCK WARNING SWITCH ASSEMBLY
  1. Inspect the unlock warning switch assembly.

    HINT:
    1. for LHD: (Click here)
    2. for RHD: (Click here)

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here)

C
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here)
A


6. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - UNLOCK WARNING SWITCH ASSEMBLY)
  1. Disconnect the E7 main body ECU connector.

  1. for LHD

    1. Disconnect the E21 unlock warning switch assembly connector.

  1. for RHD

    1. Disconnect the E90 unlock warning switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    E8-14 (KSW) - E21-2
    Always
    Below 1 Ω
    E21-1 - Body ground
    Always
    Below 1 Ω
    E8-14 (KSW) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    E8-14 (KSW) - E90-2
    Always
    Below 1 Ω
    E90-1 - Body ground
    Always
    Below 1 Ω
    E8-14 (KSW) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the unlock warning switch assembly connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Key Lock-in Prevention Function does not Work Properly (Jul 2007 – Oct 2010)PARTS LOCATION (Jul 2007 – Oct 2010) →