2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Only Back Door LOCK / UNLOCK Functions do not Operate

Circuit diagnosis · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

The back door ECU receives lock/unlock signals and activates the door lock motor accordingly.

WIRING DIAGRAM

B267287E01

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR LOCK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Back Door / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

Back Door 
Tester Display
Test Part
Control Range
Diagnostic Note
Door Lock
Operate back door lock motor
LOCK/UNLOCK
-
Result 
Result
Proceed to
Back door lock function cannot be operated
A
Back door lock function can be operated
B


B
Go to step 4
A


2. INSPECT BACK DOOR LOCK ASSEMBLY (DOOR LOCK MOTOR)
  1. Inspect the back door lock assembly (Click here).



NG
REPLACE BACK DOOR LOCK ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (BACK DOOR ECU - BACK DOOR LOCK ASSEMBLY)
  1. Disconnect the S5 back door ECU connector.

  1. Disconnect the S4 back door lock connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S5-15 (ACT+) - S4-1
    Always
    Below 1 Ω
    S5-14 (ACT-) - S4-2
    Always
    Below 1 Ω
    S5-15 (ACT+) - Body ground
    Always
    10 kΩ or higher
    S5-14 (ACT-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the back door lock connector.

  1. Reconnect the back door ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR ECU (Click here)

4. CHECK DTC OUTPUT (MULTIPLEX COMMUNICATION SYSTEM)
  1. Use an intelligent tester to check DTC output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO DTC CHART (Click here)
A


5. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Rear Lock Position SW
    Back door unlock detection switch signal / ON or OFF
    ON: Back door is unlocked
    OFF: Back door is locked
    -
    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 8
A


6. INSPECT BACK DOOR LOCK ASSEMBLY (DOOR LOCK POSITION SWITCH)
  1. Inspect the back door lock assembly (Click here).



NG
REPLACE BACK DOOR LOCK ASSEMBLY (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BACK DOOR LOCK ASSEMBLY)
  1. for LHD

    1. Disconnect the 1F main body ECU connector.

  1. for RHD

    1. Disconnect the 1K main body ECU connector.

  1. Disconnect the S4 back door lock connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    1F-4 (LSR) - S4-4
    Always
    Below 1 Ω
    S4-5 - Body ground
    Always
    Below 1 Ω
    1F-4 (LSR) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    1K-16 (LSR) - S4-4
    Always
    Below 1 Ω
    S4-5 - Body ground
    Always
    Below 1 Ω
    1K-16 (LSR) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the back door lock connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

8. INSPECT BACK DOOR LOCK CYLINDER
  1. Inspect the back door lock cylinder (Click here).



NG
REPLACE BACK DOOR LOCK CYLINDER (Click here)
OK


9. CHECK HARNESS AND CONNECTOR (BACK DOOR ECU - BACK DOOR LOCK CYLINDER)
  1. Disconnect the S5 back door ECU connector.

  1. Disconnect the S7 back door lock cylinder connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
S5-5 (L) - S7-2
Always
Below 1 Ω
S5-4 (UL) - S7-3
Always
Below 1 Ω
S5-19 (E) - S7-1
Always
Below 1 Ω
S5-5 (L) - Body ground
Always
10 kΩ or higher
S5-4 (UL) - Body ground
Always
10 kΩ or higher
S5-19 (E) - Body ground
Always
10 kΩ or higher

  1. Reconnect the back door lock cylinder connector.

  1. Reconnect the back door ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR ECU (Click here)


← Only Back Door LOCK / UNLOCK Functions do not Operate (Jul 2007 – Oct 2010)Key Lock-in Prevention Function does not Work Properly (Jul 2007 – Oct 2010) →