2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

ECM Communication Stop Mode

Circuit diagnosis · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

Detection Item
Symptom
Trouble Area
ECM Communication Stop Mode
  1. "Engine" not displayed on "Bus Check" screen of intelligent tester
  2. Applies to "ECM Communication Stop Mode" in "DTC combination table"
  1. Power source circuit of ECM
  2. ECM main wire or connector
  3. ECM

WIRING DIAGRAM

E207025E05

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the ignition switch off before inspecting CAN bus wires for a ground short.
  3. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.
  5. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here)


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (ECM MAIN WIRE)
  1. Turn the ignition switch off.

  1. E214877E02
    Disconnect the E81 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E81-32 (CANH) - E81-31 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK


3. CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. E214878E02
    Disconnect the E81, E82 and B50 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B50-14 (E01) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E81-21 (IGSW) - Body ground
    Ignition switch ON
    11 to 14 V
    E82-22 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    E82-23 (+B2) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← ECM Communication Stop Mode (Aug 2009 – Oct 2010)Combination Meter ECU Communication Stop Mode (from Nov 2010) →