2011-2016 FJ Cruiser · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built Nov 2012 – Jul 2014

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2012 Nov 2012 – Jul 2014 from Aug 2014


INSPECT FUEL INJECTOR ASSEMBLY

  1. A182852
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    11.6 to 12.4 Ω

    If the result is not as specified, replace the injector assembly.


INSPECT INJECTION VOLUME AND LEAKAGE

  1. A249692E02
    Check the injector injection.
    Text in Illustration 
    *1
    Fuel pressure Regulator
    *2
    SST (Union)
    *3
    SST (Clip)
    *4
    SST (Fuel Tube Connector)
    *5
    SST (Hose)
    *6
    SST (Adapter)
    *7
    SST (Clamp)
    *8
    Fuel injector
    *9
    Fuel Filter
    *10
    SST (T-Joint)

    CAUTION:
    1. This test involves high-pressure fuel and electricity.
    2. Take every precaution regarding safe handling of both the fuel and the electrical parts.
    3. Perform this test in a safe area, and avoid any sparks or flame.
    4. Do not smoke.


    1. Assemble SST as shown in the illustration.

      SST
      09268-31013   (09268-41091, 09268-41120, 09268-41141, 09268-41410, 09268-41500, 90467-13001, 95336-08070)

    2. Discharge the fuel system pressure (Click here).

    3. Disconnect the fuel inlet hose (fuel tube connector) from the fuel pipe.

    4. Remove the 2 bolts and disconnect the fuel pressure regulator from the fuel delivery pipe (Click here).

      NOTICE:
      Do not disconnect the No. 2 fuel pipe from the fuel pressure regulator.

    5. A174989E03
      Connect SST to the fuel pipe.
      SST
      09268-31013   (09268-41500)
      Text in Illustration 
      *1
      SST (Fuel Tube Connector)
      *2
      Fuel Filter

      CAUTION:
      Always read the precautions before connecting the fuel tube connector.

    6. A223041E02
      Connect SST (hose) to the fuel inlet of the pressure regulator with another SST (union) and the 2 bolts.
      SST
      09268-31013   (09268-41091, 95336-08070)
      Text in Illustration 
      *1
      Fuel Pressure Regulator
      *2
      SST (Hose)
      *3
      No. 2 Fuel Pipe Sub-assembly
      *4
      SST (Union)

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    7. Connect the fuel return hose to the fuel outlet of the pressure regulator.

    8. A249693E01
      Install a new O-ring to the injector.

    9. Connect SST (adapter and hose) to the injector, and hold the injector and adapter with SST (clamp).

      Text in Illustration 
      *1
      SST (Hose)
      *2
      SST (Clip)
      *3
      O-Ring
      *4
      SST (Adapter)
      *5
      Vinyl Tube
      *6
      SST (Clamp)
      SST
      09268-31013   (09268-41141, 09268-41410, 90467-13001, 95336-08070)

    10. Put the injector into a graduated cylinder.

      CAUTION:
      Install a suitable vinyl tube onto the injector assembly to prevent gasoline splashes.

    11. Operate the fuel pump (Click here).

    12. A223043E01
      Connect SST (wire) to the injector and the battery for 15 seconds, and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.
      SST
      09842-30080  
      Text in Illustration 
      *1
      SST (Wire)
      *a
      Connect

      Standard injection volume:
      71 to 86 cm3 (4.3 to 5.2 cu. in.) per 15 seconds

      Difference between each injector:
      15 cm3 (0.9 cu. in.) or less

      NOTICE:
      Always turn the voltage on and off on the battery side, not the fuel pump side.

      If the result is not as specified, replace the injector assembly.

  1. Check for fuel leaks.

    1. In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel leaks from the injector.

      Standard fuel drop:
      1 drop or less per 12 minutes

      If the fuel drop is not as specified, replace the injector assembly.

← INSPECTION (Aug 2009 – Oct 2012)INSPECTION (from Aug 2014) →