INSTALLATION
Removal / installation · Vehicles built Aug 2009 – Oct 2010
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010
| 1. INSTALL BLOWER UNIT ASSEMBLY |
![]() ![]() |
Install the 2 screws and blower unit as shown in the illustration.
| 2. INSTALL INSTRUMENT PANEL REINFORCEMENT |
Provisionally install the air conditioning unit assembly.
Insert the bracket hook into the holes of the reinforcement bracket, and provisionally install the reinforcement.
Install the instrument panel reinforcement with the 7 bolts.
Install the 2 caps.


Install the 5 bolts.
- NOTICE:
- Tighten the bolts in the sequence order shown in the illustration to install the air conditioner unit assembly.
- Torque:
- 9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for bolt
Install the 2 nuts.
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf } for nut


Engage the clamps.


Connect the connectors.
Connect the wire harness with the 3 bolts and 5 nuts.


- Torque:
- 7.3 N*m{ 74 kgf*cm , 65 in.*lbf } for nut
| 3. INSTALL COOLER UNIT DRAIN HOSE |
Install the cooler unit drain hose.

| 4. INSTALL MAIN BODY ECU (DRIVER SIDE J/B) |
Install the main body ECU with the 2 nuts.

- Torque:
- 8.4 N*m{ 86 kgf*cm , 74 in.*lbf }
| 5. INSTALL INSTRUMENT PANEL SIDE BRACKET |
Install the instrument panel side bracket with the bolt.

- Torque:
- 8.4 N*m{ 86 kgf*cm , 74 in.*lbf }
| 6. INSTALL STEERING COLUMN ASSEMBLY |
![]() ![]() |
Install the steering column assembly with the 4 nuts.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
Connect each of the connectors to the steering column assembly.
Connect the wire harness clamps to the steering column assembly.
- CAUTION:
- Use a shop rag or piece of cloth to wipe any dirt off the installation plane and column body side.
- NOTICE:
- Be careful not to scratch or soil the installation plane of the steering column.
| 7. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() ![]() |
Align the matchmarks on the steering column assembly and the steering intermediate shaft assembly.
Install the steering intermediate shaft assembly and thrust stopper onto the steering column assembly with the bolt.
- Torque:
- 36 N*m{ 367 kgf*cm , 27 ft.*lbf }
| 8. INSTALL STEERING COLUMN HOLE COVER |
![]() ![]() |
Install the steering column hole cover with the 4 clips.
- NOTICE:
- Be careful not to damage the dust seal of the steering column hole cover.
| 9. INSTALL ECM |
Install the ECM with the 3 nuts.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
Connect the 6 connectors.
| 10. INSTALL NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET |
![]() ![]() |
for LH side:
Install the instrument panel brace mounting bracket with the bolt and nut.
for RH side:

Install the instrument panel brace mounting bracket with the bolt and nut.
| 11. INSTALL NO. 1 AIR DUCT |
![]() ![]() |
Engage the 3 claws and install the air duct.
| 12. INSTALL NO. 2 AIR DUCT |
![]() ![]() |
Engage the 3 claws and install the air duct.
| 13. INSTALL REAR NO. 1 AIR DUCT |
![]() ![]() |
Engage the 6 claws and 3 clamps and install the air duct.
| 14. INSTALL REAR NO. 2 AIR DUCT |
![]() ![]() |
Engage the 6 claws and 3 clamps and install the air duct.
| 15. INSTALL NO. 1 HEATER TO REGISTER DUCT |
![]() ![]() |
Install the heater to register duct with the screw.
| 16. INSTALL NO. 2 HEATER TO REGISTER DUCT |
![]() ![]() |
Install the heater to register duct with the screw.
| 17. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY |


Install the lower instrument panel with the 2 <C> bolts, 2 <E> bolts, 7 <F> bolts and nut <G>.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt <C>
Engage the clamps and connect the connectors.
| 18. CONNECT PASSENGER AIRBAG CONNECTOR |
![]() ![]() |
Connect the passenger airbag connector.
| 19. INSTALL INSTRUMENT PANEL FINISH PANEL END LH |
Engage the 3 claws and install the instrument panel finish panel end.

| 20. INSTALL ASSIST GRIP RETAINER RH |
Install the assist grip retainer with the 2 bolts.

- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
| 21. INSTALL ASSIST GRIP RETAINER LH |
- HINT:
- Use the same procedure as for the RH side.
| 22. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY |
Connect the speaker connector.

Insert the 2 hooks into the 2 instrument panel holes and install the front speaker bracket with the 2 bolts.
- Torque:
- 2.5 N*m{ 25 kgf*cm , 22 in.*lbf }
| 23. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
Engage the 4 clips and claw and install the instrument panel speaker panel.

| 24. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
- HINT:
- Use the same procedure as for the RH side.
| 25. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY |
Install the No. 2 instrument panel register assembly (Previous Version).

Engage the 4 clips and 2 claws and install the instrument panel register.
Install the clip.
Install the No. 2 instrument panel register assembly (New Version).

Engage the 4 clips and 2 claws and install the instrument panel register.
Install the bolt and clip.
Engage the 2 claws and install the instrument panel hole cover.

| 26. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH |
Install the connectors to the instrument panel lower finish panel.

Engage the claw and 2 clips and install the instrument panel lower finish panel.
Install screw <A>.
| 27. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
Install the glove compartment door assembly with the 3 hinges while holding it horizontal.

Slightly flex the upper part of the glove compartment door assembly, and install the glove compartment door assembly.

Install the glove compartment door stoppers onto the glove compartment door.
| 28. INSTALL COMBINATION METER ASSEMBLY |
Connect the 2 connectors and the clamp.

Install the combination meter assembly with the 4 screws.

- Torque:
- 7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
| 29. INSTALL INSTRUMENT CLUSTER FINISH PANEL |
![]() ![]() |
Connect the connectors.
Engage the 3 clips and 4 claws and install the instrument cluster lower finish panel.
| 30. INSTALL LOWER INSTRUMENT PANEL LH |
Install the lower instrument panel with the 4 <F> bolts.

| 31. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
Engage the 5 clips and claw and install the lower instrument panel finish panel.

Install the 2 <F> bolts.
| 32. INSTALL INSTRUMENT PANEL FINISH PLATE |
![]() ![]() |
Install the instrument panel finish plate.
| 33. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
Engage the 3 claws and install the hood lock control lever.

| 34. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY |
Engage the 4 clips and 2 claws and install the instrument panel register.

| 35. INSTALL INSTRUMENT LOWER COVER SUB-ASSEMBLY |
Engage the 3 clips and 2 claws and install the instrument lower cover.

Install the 2 <F> bolts and 2 clips.
| 36. INSTALL CONSOLE UPPER PANEL NO. 1 GARNISH |
![]() ![]() |
Slide the console upper panel garnish toward the front of the vehicle and engage claw B.
Engage the claw A and clip and install the console upper panel garnish.
| 37. INSTALL FRONT CONSOLE BOX |
Engage the 5 claws and install the front console box.

Install the 4 <D> screws.
| 38. INSTALL BOX BOTTOM MAT |
Install the box bottom mat.

| 39. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY |
Engage the 3 claws and 5 clips and install the console upper rear panel.

| 40. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission) |
Install the shift lever knob.

| 41. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD) |
Install the shift lever knob.

| 42. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY |
![]() ![]() |
Slide the parking brake hole cover toward the rear of the vehicle and engage the 2 C claws.
Engage the 4 claws and install the parking brake hole cover.
| 43. INSTALL RADIO RECEIVER ASSEMBLY |
Connect the plug, the head unit connector and the 2 radio connectors.

Align the 2 bosses of the radio bracket with the hole in the instrument panel and install the radio receiver with the 4 bolts.

- Torque:
- 2.5 N*m{ 25 kgf*cm , 22 in.*lbf }
| 44. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY |
![]() ![]() |
Connect the 3 connectors.
Engage the 4 clips and install the integration control panel assembly.
Install the 2 <H> screws.
| 45. INSTALL INSTRUMENT PANEL GARNISH LH |
Engage the 3 clips and install the instrument panel garnish.

Install 2 <H> screws.
| 46. INSTALL INSTRUMENT PANEL GARNISH RH |
Engage the 3 clips and install the instrument panel garnish.

Install screw <H>.
| 47. INSTALL FRONT PILLAR GARNISH RH |
Engage the claw and the 2 clips and install the front pillar garnish.

| 48. INSTALL FRONT PILLAR GARNISH LH |
- HINT:
- Use the same procedure as for the RH side.
| 49. INSTALL ASSIST GRIP ASSEMBLY |
![]() ![]() |
- HINT:
- Use the same procedure to install all the assist grips.
Install the assist grip with the 2 bolts.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 50. INSTALL ASSIST GRIP PLUG |
![]() ![]() |
- HINT:
- Use the same procedure to install all the assist grip plugs.
Engage the 2 claws and install the assist grip plug.
| 51. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Install the front door opening trim weatherstrip.
| 52. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
Install the front door opening trim weatherstrip.
| 53. INSTALL COWL SIDE TRIM BOARD RH |
Engage the 2 claws and install the cowl side trim board.

Install the clip.
| 54. INSTALL COWL SIDE TRIM BOARD LH |
- HINT:
- Use the same procedure as for the RH side.
| 55. INSTALL FOOTREST CLIP |
![]() ![]() |
- HINT:
- Use the same procedure for both sides.
Engage the 2 claws and install the footrest clip.
| 56. INSTALL FRONT FLOOR FOOTREST |
Engage the 2 studs and install the front floor footrest.

| 57. INSTALL FRONT DOOR SCUFF PLATE RH |
Engage the 14 claws and install the door scuff plate.

| 58. INSTALL FRONT DOOR SCUFF PLATE LH |
- HINT:
- Use the same procedure as for the RH side.
| 59. INSTALL COMBINATION SWITCH ASSEMBLY |
Install the 3 screws.

Connect all connectors to the combination switch assembly.
| 60. INSTALL UPPER STEERING COLUMN COVER |
Engage the claw and install the upper steering column cover.

| 61. INSTALL LOWER STEERING COLUMN COVER |
Engage the 2 claws.

Install the lower steering column cover with the 3 screws.
| 62. INSTALL STEERING WHEEL ASSEMBLY |
Align the matchmarks on the steering wheel assembly and steering main shaft assembly.
Install the steering wheel assembly set nut.
- Torque:
- 50 N*m{ 510 kgf*cm , 37 ft.*lbf }
| 63. INSTALL STEERING PAD |
Support the steering pad with one hand as shown in the illustration.

Connect the 2 connectors to the steering pad.
- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
Connect the horn connector.
Confirm that the circumferencial groove of the "Torx" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
Using "Torx" socket wrench (T30), tighten the 2 "Torx" screws.
- Torque:
- 8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
- NOTICE:
- Tighten the 2 bolts while holding the steering pad to prevent it from moving upward.
| 64. INSTALL LOWER NO. 2 STEERING WHEEL COVER |
Install steering wheel cover lower No.2.

| 65. INSTALL LOWER NO. 3 STEERING WHEEL COVER |
Install steering wheel cover lower No.2.

| 66. CONNECT HEATER WATER OUTLET HOSE A (FROM HEATER UNIT) |
![]() ![]() |
Install the heater water outlet hose onto the heater unit.
- NOTICE:
- Perform the installation with the hose clip and mark at the correct angle as shown in the illustration.
| 67. CONNECT HEATER WATER HOSE INLET |
![]() ![]() |
Install the heater water inlet hose onto the heater unit.
- NOTICE:
- Perform the installation with the hose clip and mark at the correct angle as shown in the illustration.
| 68. INSTALL COOLER REFRIGERANT LIQUID PIPE A |
![]() ![]() |
Remove the vinyl tape from liquid tube A and the connecting portion of the unit.
Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the connecting part of the liquid pipe.
- Compressor oil:
- ND-OIL8 or the equivalent
Install the O-ring onto the liquid pipe.
Install the liquid and piping clamp.
- HINT:
- After connection, check the claw fitting of the piping clamp.
| 69. INSTALL COOLER REFRIGERANT SUCTION PIPE A |
- HINT:
- Connection procedure of the suction pipe is the same as for the liquid pipe.
| 70. INSTALL COWL TOP VENTILATOR LOUVER LH |
Install the cowl top ventilator louver LH with the 5 clips and engage the 7 claws.

| 71. INSTALL COWL TOP VENTILATOR LOUVER RH |
Install the cowl top ventilator louver RH with the 3 clips and the claw.

Install the hood to cowl top seal with the clip.
| 72. INSTALL COWL TOP VENTILATOR LOUVER ASSEMBLY |
Install the cowl top ventilator louver sub-assembly with the 7 clips.

| 73. INSTALL FRONT FENDER SIDE PANEL UPPER LH |
Install the 4 new clips on the front fender side panel upper LH.
Engage the 4 clips and install the front fender side panel upper LH.

| 74. INSTALL FRONT FENDER SIDE PANEL UPPER RH |
Install the 4 new clips on the front fender side panel upper RH.
Engage the 4 clips and install the front fender side panel upper RH.

| 75. INSTALL ANTENNA ORNAMENT |
Press in the antenna ornament in the direction shown in the illustration.

| 76. INSTALL ROOF ANTENNA POLE SUB-ASSEMBLY |
![]() ![]() |
Install the radio antenna pole by turning it in the direction of the arrow shown in the illustration.
- Torque:
- 3.3 N*m{ 35 kgf*cm , 29 in.*lbf }
- NOTICE:
- Use a short wrench, tighten with your finger, not your hand.
| 77. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Align the blade tip with the mark on the windshield glass, as shown in the illustration.

Tighten the nut of the front wiper arm.
- Torque:
- 25 N*m{ 255 kgf*cm , 18 ft.*lbf }
| 78. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (CENTER SIDE) |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Align the blade tip with the mark on the windshield glass, as shown in the illustration.

Tighten the nut of the front wiper arm.
- Torque:
- 25 N*m{ 255 kgf*cm , 18 ft.*lbf }
| 79. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Align the blade tip with the mark on the windshield glass, as shown in the illustration.

Tighten the nut of the front wiper arm.
- Torque:
- 25 N*m{ 255 kgf*cm , 18 ft.*lbf }
| 80. INSTALL WINDSHIELD WIPER ARM COVER |
Engage the claw and install the 3 front wiper arm cover.

| 81. ADD ENGINE COOLANT |
Tighten the 2 cylinder block drain cock plugs.
- Torque:
- 13 N*m{ 130 kgf*cm , 9 ft.*lbf }
Tighten the radiator drain cock plug by hand.
Add engine coolant.
- Standard Capacity:
Item
Specified Condition
for Automatic Transmission
9.8 liters (10.4 US qts, 8.6 Imp. qts)
for Manual Transmission
9.4 liters (9.9 US qts, 8.3 Imp. qts)
- NOTICE:
- Do not substitute plain water for engine coolant.
- HINT:
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
Slowly pour coolant into the radiator reservoir until it reaches the Full line.

Text in Illustration *1
FULL Line
Install the reservoir cap.
Install the radiator cap.*1
Start the engine and stop it immediately.*2
Allow approximately 10 seconds to pass, and then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3
Repeat steps *1, *2 and *3 until the coolant level does not decrease.
- HINT:
- Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator if the engine is warmed up and the thermostat opens.
Install the radiator cap.*4
Set the air conditioning as follows.*5
Item
Condition
Fan speed
Any setting except off
Temperature
Toward WARM
Air conditioning switch
Off
Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6
- CAUTION:
- Wear protective gloves. Hot areas on the parts may injure your hands.
- Be careful of the fan.
- Be careful as the engine, radiator and radiator hoses are hot and can cause burns.
- Wear protective gloves. Hot areas on the parts may injure your hands.
- NOTICE:
- Immediately after starting the engine, if the radiator reservoir becomes empty, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the Full line.
- Do not start the engine when there is no coolant in the radiator reservoir.
- Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
- If there is not enough coolant, the engine may burn out or overheat.
- Immediately after starting the engine, if the radiator reservoir becomes empty, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the Full line.
- HINT:
- Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air while warming up the engine.
- The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.
- Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air while warming up the engine.
Stop the engine, wait until the engine coolant cools down to ambient temperature, and then remove the radiator cap and check the coolant level.*7
- CAUTION:
- Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8
If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the Full line.

If the coolant level is below the Full line, repeat steps *4 through *8.
If the coolant level is above the Full line, drain coolant until the coolant level reaches the Full line.Text in Illustration *1
FULL Line
| 82. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 3.9 N*m{ 40 kgf*cm , 35 in.*lbf }
| 83. CHECK SRS WARNING LIGHT |
| 84. CHARGE REFRIGERANT |


- NOTICE:
- Charge refrigerant in accordance with the equipment manual.
Perform vacuum purging using a vacuum pump.
Charge refrigerant HFC-134a (R134a).
- SST
- 09985-20010
(09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)
- Standard:
- 570 to 630 g (20.11 to 22.22 oz.)
- NOTICE:
- Do not start the engine before charging it with refrigerant as the cooler compressor doesn't work properly without sufficient refrigerant. This could cause the compressor to overheat.
- Approximately 100 g (3.5 oz.) of refrigerant may need to be charged after bubbles disappear.
The volume of refrigerant should be measured, not checked with the sight glass.
- Do not start the engine before charging it with refrigerant as the cooler compressor doesn't work properly without sufficient refrigerant. This could cause the compressor to overheat.
- HINT:
- The relationship between the refrigerant charge amount and the pressure is as follows.


- High Charge Range:
If the refrigerant is overcharged, the pressure rises on the high-pressure side. High-pressure cut off frequently occurs. This causes insufficient cooling performance and also insufficient compressor lubrication.
- Low Charge Range:
A shortage of refrigerant causes insufficient cooling performance and low circulation of refrigerant oil, which shortens the compressor life. Operation with insufficient coolant raises the refrigerant temperature and causes heat deterioration of the rubber seals and hoses. Cracking and subsequent refrigerant leakage may occur.
- The relationship between the refrigerant charge amount and the pressure is as follows.
Install the caps onto the service valves on the refrigerant line.
| 85. WARM UP ENGINE |
- NOTICE:
- Warm up the engine at less than 2,000 rpm for 1 minute or more after charging it with refrigerant.
| 86. CHECK FOR ENGINE COOLANT LEAK |
- CAUTION:
- To avoid being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion may cause hot engine coolant and steam to blow out from the radiator.
Fill the radiator with engine coolant, and then attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and then check that the pressure does not drop.

If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.Text in Illustration *1
Radiator Cap Tester
| 87. CHECK FOR REFRIGERANT LEAK |
After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.
Perform the operation as follows:
- Stop the engine.
- Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
- Repeat the test 2 or 3 times.
- Make sure that some refrigerant remains in the refrigeration system.
When the compressor is off: approximately 392 to 588 kPa (4 to 6 kgf*cm2, 57 to 85 psi)
- HINT:
- It is impossible for the above pressure to be maintained if there is leakage.
- Stop the engine.
Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.

Bring the halogen leak detector close to the drain hose before performing the test.

- HINT:
- After the blower motor has stopped, leave the cooling unit for at least 15 minutes.
- Place the halogen leak detector sensor under the drain hose.
- When bringing the halogen leak detector close to the drain hose, make sure that the halogen leak detector does not react to the volatile gases.
- After the blower motor has stopped, leave the cooling unit for at least 15 minutes.
If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.
| 88. POSITION FRONT WHEELS FACING STRAIGHT AHEAD |
























