2011-2016 FJ Cruiser · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Aug 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


CLEAN CYLINDER HEAD SUB-ASSEMBLY

A053862E01
  1. Using a gasket scraper, remove all the gasket material from the surface which contacts the cylinder block.

    NOTICE:
    Be careful not to scratch the surface which contacts the cylinder block.

  1. A053863E01
    Using a wire brush, remove all the carbon from the combustion chambers.

    NOTICE:
    Be careful not to scratch the cylinder block contact surface.

  1. A053864E01
    Using a valve guide bushing brush and solvent, clean all the guide bushes.

  1. A053865E01
    Using a soft brush and solvent, thoroughly clean the cylinder head.


INSPECT CYLINDER HEAD SUB-ASSEMBLY

A221108E02
  1. Using a precision straightedge and feeler gauge, measure the warpage of the surfaces which contact the cylinder block sub-assembly and manifolds.

    Text in Illustration 
    *a
    Cylinder Block Side:
    *b
    Intake Side:
    *c
    Exhaust Side:

    Standard Warpage:
    Item
    Specified Condition
    Cylinder block side
    0.05 mm (0.00197 in.)
    Intake side
    0.08 mm (0.00315 in.)
    Exhaust side
    0.08 mm (0.00315 in.)

    Maximum Warpage:
    Item
    Specified Condition
    Cylinder block side
    0.10 mm (0.00394 in.)
    Intake side
    0.10 mm (0.00394 in.)
    Exhaust side
    0.10 mm (0.00394 in.)

    If the warpage is more than the maximum, replace the cylinder head sub-assembly.

  1. Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
    If cracked, replace the cylinder head sub-assembly.


CLEAN VALVE SEAT

A053829E04
  1. Using a 45° carbon cutter, resurface the valve seats.

    Text in Illustration 
    *1
    45° Carbon Cutter

    HINT:
    Only remove the amount of metal necessary to clean the seats.


INSPECT INTAKE VALVE

A053867E03
  1. Clean the valves.

    1. Using a gasket scraper, chip off any carbon from the valve head.

    2. Using a wire brush, thoroughly clean the valve.

  1. Using a micrometer, measure the diameter of the valve stem.

    Valve stem diameter:
    5.470 to 5.485 mm (0.215 to 0.216 in.)

    If the valve stem diameter is not as specified, check the oil clearance.

  1. A053834E11
    Check the valve face angle.
    Text in Illustration 
    *a
    Valve Face Angle

    1. Grind the valve sufficiently to remove pits and carbon.

    2. Check that the valve is ground to the correct valve face angle.

      Standard valve face angle:
      45.5°

  1. A121379E06
    Using a vernier caliper, measure the valve head margin thickness.
    Text in Illustration 
    *a
    Margin Thickness

    Standard margin thickness:
    1.25 mm (0.0492 in.)

    Minimum margin thickness:
    0.5 mm (0.0197 in.)

    If the margin thickness is less than the minimum, replace the intake valve.

  1. Using a vernier caliper, measure the valve overall length.

    Standard overall length:
    105.85 mm (4.17 in.)

    Minimum overall length:
    105.35 mm (4.15 in.)

    If the overall length is less than the minimum, replace the intake valve.


INSPECT EXHAUST VALVE

A053867E03
  1. Clean the valves.

    1. Using a gasket scraper, chip off any carbon from the valve head.

    2. Using a wire brush, thoroughly clean the valve.

  1. Using a micrometer, measure the diameter of the valve stem.

    Valve stem diameter:
    5.465 to 5.480 mm (0.215 to 0.216 in.)

    If the valve stem diameter is not as specified, check the oil clearance.

  1. A053834E11
    Check the valve face angle.
    Text in Illustration 
    *a
    Valve Face Angle

    1. Grind the valve sufficiently to remove pits and carbon.

    2. Check that the valve is ground to the correct valve face angle.

      Standard valve face angle:
      45.5°

  1. A121382E07
    Using a vernier caliper, measure the valve head margin thickness.
    Text in Illustration 
    *a
    Margin Thickness

    Standard margin thickness:
    1.4 mm (0.0551 in.)

    Minimum margin thickness:
    0.5 mm (0.0197 in.)

    If the margin thickness is less than the minimum, replace the exhaust valve.

  1. Using a vernier caliper, measure the valve overall length.

    Standard overall length:
    110.40 mm (4.35 in.)

    Minimum overall length:
    109.90 mm (4.33 in.)

    If the overall length is less than the minimum, replace the exhaust valve.


INSPECT VALVE GUIDE BUSH OIL CLEARANCE

A120707
  1. Using a caliper gauge, measure the inside diameter of the valve guide bush.

    Bush inside diameter:
    5.510 to 5.530 mm (0.217 to 0.218 in.)

  1. Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

    Standard Clearance:
    Item
    Specified Condition
    Intake
    0.025 to 0.060 mm (0.000984 to 0.00236 in.)
    Exhaust
    0.030 to 0.065 mm (0.00118 to 0.00256 in.)

    Maximum Oil Clearance:
    Item
    Specified Condition
    Intake
    0.08 mm (0.00315 in.)
    Exhaust
    0.10 mm (0.00394 in.)

    If the clearance is more than the maximum, replace the valve and valve guide bush.


INSPECT INTAKE VALVE SEAT
  1. Apply a light coat of Prussian blue to the valve face.

  1. Lightly press the valve face against the valve seat.

    NOTICE:
    Do not rotate the valve.

  1. A094929E06
    Check the valve face and valve seat by using the following procedure:
    Text in Illustration 
    *a
    Width

    1. Check that Prussian blue appears around the entire valve face. If not, replace the valve.

    2. If Prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve seat.

    3. Check that the valve seat contacts the middle of the valve face with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).


INSPECT EXHAUST VALVE SEAT
  1. Apply a light coat of Prussian blue to the valve face.

  1. Lightly press the valve face against the valve seat.

    NOTICE:
    Do not rotate the valve.

  1. A094929E06
    Check the valve face and valve seat by using the following procedure:
    Text in Illustration 
    *a
    Width

    1. Check that Prussian blue appears around the entire valve face. If not, replace the valve.

    2. If Prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve seat.

    3. Check that the valve seat contacts the middle of the valve face with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).


INSPECT INNER COMPRESSION SPRING

  1. A109669
    Using a vernier caliper, measure the free length of the inner compression spring.

    Standard free length:
    48.63 mm (1.91 in.)

    If the free length is not as specified, replace the inner compression spring.

  1. A094933E04
    Using a steel square, measure the deviation of the inner compression spring.
    Text in Illustration 
    *a
    Deviation

    Maximum deviation:
    1.0 mm (0.0394 in.)

    Maximum angle (reference):
    2°

    If the deviation is more than the maximum, replace the inner compression spring.

  1. A106674
    Using a spring tester, measure the tension of the valve spring when it is compressed to the specified installation length.

    Standard installed tension:
    236 to 260 N (24 to 27 kgf, 53.0 to 58.5 lbf) at 36.9 mm (1.45 in.)

    If the installed tension is not as specified, replace the valve spring.

← INSPECTION (Jul 2007 – Jul 2009)REPLACEMENT (Jul 2007 – Jul 2009) →