2011-2016 FJ Cruiser · Service Manual ENGINE

P0013 Camshaft Position "B" Actuator Circuit / Open (Bank 1)

Diagnostic trouble codes · Vehicles built from Aug 2009

Also covers:

DESCRIPTION

  1. This DTC is designed to detect opens or shorts in the Camshaft Timing Oil Control Valve (OCV) assembly circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.
  2. The VVT (variable valve timing) system adjusts the valve timing to improve the driveability. The engine oil pressure turns the camshaft timing exhaust gear assembly to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 volts to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.
A209140E09
DTC No.
DTC Detection Condition
Trouble Area
P0013
Open or short in OCV (for exhaust side of bank 1) circuit
(1 trip detection logic)
  1. Open or short in OCV (for exhaust side of bank 1) circuit
  2. OCV (for exhaust side of bank 1)
  3. ECM
P0023
Open or short in OCV (for exhaust side of bank 2) circuit
(1 trip detection logic)
  1. Open or short in OCV (for exhaust side of bank 2) circuit
  2. OCV (for exhaust side of bank 2)
  3. ECM

MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the Camshaft Timing Oil Control Valve (OCV) assembly circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

A178641E05

INSPECTION PROCEDURE

HINT:
  1. If DTC P0013 is displayed, check the VVT system for exhaust side of bank 1 circuit.
  2. Bank 1 refers to the bank that includes No. 1 cylinder.
  3. If DTC P0023 is displayed, check the bank 2 VVT system for exhaust side of bank 2 circuit.
  4. Bank 2 refers to the bank that does not include No. 1 cylinder.
  5. Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK DTC (P0013 OR P0023)
  1. Connect the intelligent tester to the DLC3.

  1. Clear DTC after recording the freeze frame data and DTC (Click here).

  1. Turn the ignition switch off.

  1. Allow the engine to idle and check DTC.

  1. Check that P0013 or P0023 is not present.

    OK:
    P0013 or P0023 is not present.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A160397E17
    Disconnect the OCV connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Camshaft Timing Oil Control Valve Assembly)



NG
REPLACE CAMSHAFT TIMNG OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (OCV - ECM)
  1. Disconnect the OCV connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B55-1 - B48-21 (OE1+)
    Always
    Below 1 Ω
    B55-2 - B48-22 (OE1-)
    Always
    Below 1 Ω
    B56-1 - B47-21 (OE2+)
    Always
    Below 1 Ω
    B56-2 - B47-22 (OE2-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B55-1 or B48-21 (OE1+) - Body ground
    Always
    10 kΩ or higher
    B55-2 or B48-22 (OE1-) - Body ground
    Always
    10 kΩ or higher
    B56-1 or B47-21 (OE2+) - Body ground
    Always
    10 kΩ or higher
    B56-2 or B47-22 (OE2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) (+ P0012, P0021, P0022) (from Aug 2014)P0014 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1) (+ P0015, P0024, P0025) (Aug 2009 – Oct 2010) →