2011-2016 FJ Cruiser · Service Manual RESTRAINTS

Driver Side Seat Belt Warning Light does not Operate

Circuit diagnosis · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

  1. When the ignition switch is ON, the combination meter assembly receives signals from the front seat inner belt assembly (driver side). When the seat belt is unfastened, the combination meter assembly flashes the driver seat belt warning light in the combination meter assembly. When the seat belt is fastened, the combination meter assembly stops flashing the front driver seat belt warning light.

WIRING DIAGRAM

B137675E02

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (D SEAT BUCKLE SW)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester on.

  1. Enter the following menus: Body / Body / Data List.

    Body:
    Tester Display
    Measurement Item/ Range
    Normal Condition
    Diagnostic Note
    D Seat Buckle SW
    Driver Seat belt buckle switch: ON or OFF
    ON: Driver seat belt is fastened
    OFF: Driver seat belt is unfastened
    -

    OK:
    Front seat inner belt assembly (driver side) operates normally.



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY)
B137678E03
  1. Disconnect the E13 combination meter assembly connector.

  1. Disconnect the L19 front seat inner belt assembly (driver side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E13-8 (L) - L19-3 (+)
    Always
    Below 1 Ω
    E13-8 (L) or L19-3 (+) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the combination meter assembly connector.

  1. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

3. INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)
B137709E03
  1. Disconnect the L19 front seat inner belt assembly (driver side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    + - E
    Tongue plate fastened
    10 kΩ or higher
    RDC - E
    Tongue plate unfastened
    10 kΩ or higher
    + - E
    Tongue plate unfastened
    Below 1 Ω
    RDC - E
    Tongue plate fastened
    Below 1 Ω

  1. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT SEAT INNER BELT ASSEMBLY)
B137679E02
  1. Disconnect the E6 main body ECU connector.

  1. Disconnect the L19 front seat inner belt assembly (driver side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-13 (DBKL) - L19-3 (+)
    Always
    Below 1 Ω
    E6-13 (DBKL) or L19-3 (+) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY - BODY GROUND)


← ON-VEHICLE INSPECTION (from Jul 2007)Driver Side Seat Belt Warning Light does not Operate (from Nov 2010) →