2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1815/54 Short in Front Passenger Side Squib 2nd Step Circuit

Diagnostic trouble codes · Vehicles built from Nov 2010

Also covers:

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

The front passenger side squib 2nd step circuit consists of the center airbag sensor assembly and the front passenger airbag assembly.
The circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side squib 2nd step circuit.
DTC No.
DTC Detecting Condition
Trouble Area
B1815/54
  1. Center airbag sensor assembly detects line short circuit signal in front passenger side squib 2nd step circuit 5 times during primary check.
  2. Front passenger side squib 2nd step malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag assembly (Front passenger side squib 2nd step)
  4. Center airbag sensor assembly
B1816/54
  1. Center airbag sensor assembly detects open circuit signal in front passenger side squib 2nd step circuit for 2 seconds.
  2. Front passenger side squib 2nd step malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag assembly (Front passenger side squib 2nd step)
  4. Center airbag sensor assembly
B1817/54
  1. Center airbag sensor assembly detects short circuit to ground signal in front passenger side squib 2nd step circuit for 0.5 seconds.
  2. Front passenger side squib 2nd step malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag assembly (Front passenger side squib 2nd step)
  4. Center airbag sensor assembly
B1818/54
  1. Center airbag sensor assembly detects short circuit to B+ signal in front passenger side squib 2nd step circuit for 0.5 seconds.
  2. Front passenger side squib 2nd step malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag assembly (Front passenger side squib 2nd step)
  4. Center airbag sensor assembly

WIRING DIAGRAM

C146249E30

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the Techstream (Click here).
  2. After selecting CHECK MODE (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK CONNECTOR (FRONT PASSENGER AIRBAG - INSTRUMENT PANEL WIRE ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check the instrument panel wire assembly connector and terminals (on the front passenger airbag side) and the connector is properly connected to the front passenger airbag.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE INSTRUMENT PANEL WIRE ASSEMBLY

C
CONNECT CONNECTOR PROPERLY
A


2. CHECK FRONT PASSENGER AIRBAG (FRONT PASSENGER SIDE SQUIB 2ND STEP)

  1. H100867E02
    Disconnect the connectors from the front passenger airbag assembly.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to connector E (black connector).

    CAUTION:
    Never connect a tester to the front passenger airbag assembly (front passenger side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert the SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1815/54, B1816/54, B1817/54 and B1818/54 are not output.

    HINT:
    DTCs other than DTC B1815/54, B1816/54, B1817/54 and B1818/54 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE FRONT PASSENGER AIRBAG (Click here)

3. CHECK CONNECTOR (INSTRUMENT PANEL WIRE ASSEMBLY - INSTRUMENT PANEL WIRE)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector E.

  1. Check the instrument panel wire assembly connector and terminals (on the instrument panel wire side) and check the connector is properly connected to the instrument panel wire.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE INSTRUMENT PANEL WIRE ASSEMBLY

C
CONNECT CONNECTOR PROPERLY
A


4. CHECK INSTRUMENT PANEL WIRE ASSEMBLY
  1. Disconnect the instrument panel wire connector from the instrument panel wire assembly.

  1. C127737E02
    Check for short to B+ in the circuit.
    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch on.

    3. Measure the voltage.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      Y2-2 (P2-) - Body ground
      Ignition switch on
      Below 1 V
      Y2-1 (P2+) - Body ground
      Ignition switch on
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Y2-2 (P2-) - Y2-1 (P2+)
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Y2-2 (P2-) - Body ground
      Always
      1 MΩ or higher
      Y2-1 (P2+) - Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector D (Click here).

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Y2-2 (P2-) - Y2-1 (P2+)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector D to the original condition.



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE ASSEMBLY
OK


5. CHECK CONNECTOR (INSTRUMENT PANEL WIRE - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Disconnect the connector from the center airbag sensor assembly.

  1. Check the instrument panel wire connector and terminals (on the center airbag sensor assembly side) and check the connector is properly connected to the center airbag sensor assembly.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPAIR OR REPLACE INSTRUMENT PANEL WIRE

C
CONNECT CONNECTOR PROPERLY
A


6. CHECK INSTRUMENT PANEL WIRE

  1. H100861E08
    Check for short to B+ in the circuit.
    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch on.

    3. Measure the voltage.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      EY1-3 (P2+) - Body ground
      Ignition switch on
      Below 1 V
      EY1-4 (P2-) - Body ground
      Ignition switch on
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      EY1-3 (P2+) - EY1-4 (P2-)
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      EY1-3 (P2+) - Body ground
      Always
      1 MΩ or higher
      EY1-4 (P2-) - Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      EY1-3 (P2+) - EY1-4 (P2-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


7. CHECK CENTER AIRBAG SENSOR ASSEMBLY
  1. Connect the instrument panel wire connector to the instrument panel wire assembly.

  1. H100860E02
    Connect the connectors to the front passenger airbag assembly and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1815/54, B1816/54, B1817/54 and B1818/54 are not output.

    HINT:
    DTCs other than DTC B1815/54, B1816/54, B1817/54 and B1818/54 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1815/54 Short in Front Passenger Side Squib 2nd Step Circuit (+ B1816/54, B1817/54, B1818/54) (Jul 2007 – Oct 2010)B1820/55 Short in Side Squib RH Circuit (+ B1821/55, B1822/55, B1823/55) (from Aug 2012) →