2011-2016 FJ Cruiser · Service Manual BODY

TERMINALS OF ECU

System information · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2011 from Aug 2011


CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
B112770E02
  1. Disconnect the H5 switch connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Standard:
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H5-9 (B) - Body ground
    W - Body ground
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    H5-9 (B) - Body ground
    W - Body ground
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    H5-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the H5 switch connector.

  4. Measure the voltage of the connector.

    Standard voltage:
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H5-3 (U) - H5-1 (E)
    L - W-B
    Power window motor UP output
    Ignition switch ON, driver side power window switch OFF → UP (manual operation)
    Below 1 V → 11 to 14 V
    H5-4 (D) - H5-1 (E)
    L-B - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window switch OFF → DOWN (manual operation)
    Below 1 V → 11 to 14 V
    H5-4 (D) - H5-1 (E)
    L-B - W-B
    Power window motor DOWN output
    Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open
    Below 1 V → 11 to 14 V → Below 1 V

    If the result is not as specified, the master switch may have a malfunction.

  5. Check the AUTO light illumination.

    1. After turning the ignition switch ON, check that the AUTO light illuminates (amber).


CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY
B121518E15
  1. Disconnect the G6 power window regulator switch assembly connector.

  2. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G6-4 (B) - Body ground
    W - Body ground
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    G6-4 (B) - Body ground
    W - Body ground
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    G6-1 (D) - Body ground
    L-B - Body ground
    Power window motor DOWN output
    Ignition switch ON, power window switch OFF → DOWN
    Below 1 V → 11 to 14 V
    G6-2 (SD) - Body ground
    R - Body ground
    Power window motor DOWN input (Remote)
    Ignition switch ON, power window master switch OFF → DOWN (Remote)
    Below 1 V → 11 to 14 V
    G6-3 (U) - Body ground
    L - Body ground
    Power window motor UP output
    Ignition switch ON, power window switch OFF → UP
    Below 1 V → 11 to 14 V
    G6-5 (SU) - Body ground
    R-B - Body ground
    Power window motor UP input (Remote)
    Ignition switch ON, power window master switch OFF → UP (Remote)
    Below 1 V → 11 to 14 V

    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the G6 power window regulator switch assembly connector.

← PROBLEM SYMPTOMS TABLE (from Aug 2011)TERMINALS OF ECU (Nov 2010 – Jul 2011) →