2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Illumination Circuit

Circuit diagnosis · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

CAUTION / NOTICE / HINT


DESCRIPTION

Power is supplied to the radio receiver and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E219826E01

INSPECTION PROCEDURE

CAUTION:
  1. The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution for the SRS (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK ILLUMINATION
  1. Check if the illumination for the multi-display, steering pad switch, glove box light, cigarette lighter, or others (seat heater switch, front seat memory switch, etc.) comes on when the light control switch is turned to the head or tail position.

    Result 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except radio receiver.
    B
    No illumination comes on for radio receiver, back sonar switch, hazard switch, cigarette lighter, etc.
    C
    Illumination comes on for all components except steering pad switch and radio receiver assembly.
    D



B
Go to step 6

C
GO TO LIGHTING SYSTEM (Click here)

D
Go to step 7
A


2. CHECK HARNESS AND CONNECTOR (TAIL RELAY - SPIRAL CABLE)

  1. E172054E02
    Disconnect the E17 spiral cable connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E17-1 (ILL+) - Body ground
    Light control switch head or tail
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral Cable)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT STEERING PAD SWITCH ASSEMBLY (STEERING PAD SIDE)
E219841E01
  1. Disconnect the steering pad switch connector.

  1. Apply battery voltage to the terminals of the connector, and check the LED illumination condition.

    OK 
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1 (ILL+)
    Battery negative (-) → Terminal 10 (EAU)
    Light illuminates



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


4. INSPECT SPIRAL CABLE SUB-ASSEMBLY
E219813E02
  1. Remove the spiral cable (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-1 (ILL+) - B-1 (ILL+)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    A-10 (EAU) - B-10 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    Text in Illustration 
    *a
    Vehicle Side
    *b
    Steering Pad Switch Side

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)
  1. Disconnect the E17 spiral cable connector.

  1. Disconnect the E43 radio receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E43-6 (SWG) - E17-10 (EAU)
    Always
    Below 1 Ω
    E43-6 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

6. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - TAIL RELAY)

  1. E219852E01
    Disconnect the E85*1 or E41*2 receiver connector.*1: for 10 Speaker with Sub-Woofer*2: for 6 Speaker

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (for 10 Speaker with Sub-Woofer):
    Tester Connection
    Switch Condition
    Specified Condition
    E85-2 (ILL+) - Body ground
    Light control switch head or tail
    11 to 14 V

    Standard Voltage (for 6 Speaker):
    Tester Connection
    Switch Condition
    Specified Condition
    E41-10 (ILL+) - Body ground
    Light control switch head or tail
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio Receiver Assembly (for 10 Speaker with Sub-Woofer))
    *b
    Front view of wire harness connector
    (to Radio Receiver Assembly (for 6 Speaker))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

7. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BODY GROUND)

  1. E219852E02
    Disconnect the E85*1 or E41*2 receiver connector.*1: for 10 Speaker with Sub-Woofer*2: for 6 Speaker

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for 10 Speaker with Sub-Woofer):
    Tester Connection
    Condition
    Specified Condition
    E85-12 (ILL-) - Body ground
    Always
    Below 1 Ω

    Standard Resistance (for 6 Speaker):
    Tester Connection
    Condition
    Specified Condition
    E41-5 (ILL-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio Receiver Assembly (for 10 Speaker with Sub-Woofer))
    *b
    Front view of wire harness connector
    (to Radio Receiver Assembly (for 6 Speaker))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Illumination Circuit (Jul 2007 – Oct 2010)Speaker Circuit (Jul 2007 – Oct 2010) →