Illumination Circuit
Circuit diagnosis · Vehicles built Jul 2007 – Oct 2010
Versions by build date: Jul 2007 – Oct 2010 from Nov 2010
DESCRIPTION
Power is supplied to the radio receiver and steering pad switch assembly illumination when the light control switch is in the TAIL or HEAD position.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the supplemental restraint system (Click here).
| 1. CHECK ILLUMINATION |
Check if the illumination for the radio receiver, steering pad switch, or other lights (back sonar switch, hazard switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.
- Result:
Result
Proceed to
Illumination comes on for all components except steering pad switch.
A
Illumination comes on for all components except radio receiver.
B
No illumination comes on (radio receiver, back sonar switch, hazard switch, etc.).
C
|
|
||||
|
|
||||
| A | |
| 2. INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch assembly connector.
Connect the positive (+) lead to terminal ILL+ and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.


Check if the illumination for the steering pad switch assembly comes on.
- OK:
- Illumination for the steering pad switch assembly comes on.
|
|
||||
| OK | |
| 3. INSPECT SPIRAL CABLE |
Disconnect the E17 steering pad switch assembly and spiral cable connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester connection
Condition
Specified condition
Terminal 10 (EAU) main switch side - EAU (E17-10)
Always
Below 1 Ω
Terminal 1 (ILL+) main switch side - ILL+ (E17-1)
Always
Below 1 Ω
- NOTICE:
- The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.
Reconnect the steering pad switch assembly connector.
Reconnect the spiral cable connector.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE) |
Disconnect the E17 spiral cable connector.

Measure the voltage according to the value in the table below.
- Standard voltage:
Tester connection
Condition
Specified condition
E17-1 (ILL+) - Body ground
Light control SW TAIL or HEAD
11 to 14 V
Reconnect the spiral cable connector.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER) |
Disconnect the E43 radio receiver connector.

Disconnect the E17 spiral cable connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E43-6 (SWG) - E17-10 (SWG)
Always
Below 1 Ω
E43-6 (SWG) or E17-10 (SWG) - Body ground
Always
10 kΩ or higher
Reconnect the radio receiver connector.
Reconnect the spiral cable connector.
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER) |
Disconnect the E41 radio receiver connector.

Measure the voltage according to the value in the table below.
- Standard voltage:
Tester connection
Switch Condition
Specified condition
E41-10 (ILL+) - Body ground
Light control SW TAIL or HEAD
11 to 14 V
Reconnect the radio receiver connector.
|
|
||||
| OK | ||
| ||
