2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Steering Pad Switch Circuit

Circuit diagnosis · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as that when the switch is continuously depressed occurs.
Therefore, the radio receiver cannot be operated using the steering pad switch, and also the radio receiver itself cannot function.

WIRING DIAGRAM

E148138E01

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).


1. INSPECT RADIO RECEIVER

  1. E130767E01
    Disconnect the E43 radio receiver connector.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    E43-7 (SW1) - E43-6 (SWG)
    No switches pushed
    Approximately 100 kΩ
    E43-7 (SW1) - E43-6 (SWG)
    SEEK+ switch pushed
    Approximately 0 Ω
    E43-7 (SW1) - E43-6 (SWG)
    SEEK- switch pushed
    Approximately 0.3 kΩ
    E43-7 (SW1) - E43-6 (SWG)
    VOL+ switch pushed
    Approximately 1 kΩ
    E43-7 (SW1) - E43-6 (SWG)
    VOL- switch pushed
    Approximately 3.2 kΩ
    E43-8 (SW2) - E43-6 (SWG)
    No switches pushed
    Approximately 100 kΩ
    E43-8 (SW2) - E43-6 (SWG)
    MODE switch pushed
    Approximately 0 Ω

  1. Reconnect the radio receiver connector.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

2. INSPECT STEERING PAD SWITCH ASSEMBLY

  1. Disconnect the E17 steering pad switch assembly connector.E130787E01

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    E17-12 (AU1) - E17-10 (EAU)
    No switches pushed
    Approximately 100 kΩ
    E17-12 (AU1) - E17-10 (EAU)
    SEEK+ switch pushed
    Approximately 0 Ω
    E17-12 (AU1) - E17-10 (EAU)
    SEEK- switch pushed
    Approximately 0.3 kΩ
    E17-12 (AU1) - E17-10 (EAU)
    VOL+ switch pushed
    Approximately 1 kΩ
    E17-12 (AU1) - E17-10 (EAU)
    VOL- switch pushed
    Approximately 3.2 kΩ
    E17-11 (AU2) - E17-10 (EAU)
    No switches pushed
    Approximately 100 kΩ
    E17-11 (AU2) - E17-10 (EAU)
    MODE switch pushed
    Approximately 0 Ω

  1. Reconnect the steering pad switch assembly connector.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


3. INSPECT SPIRAL CABLE

  1. B133361E02
    Disconnect the E17 steering pad switch assembly and spiral cable connectors.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Specified condition
    Terminal 10 (EAU) main switch side - EAU (E17-10)
    Below 1 Ω
    Terminal 12 (AU1) main switch side - AU1 (E17-12)
    Below 1 Ω
    Terminal 11 (AU2) main switch side - AU2 (E17-11)
    Below 1 Ω

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

  1. Reconnect the steering pad switch assembly connector.

  1. Reconnect the spiral cable connector.



NG
REPLACE SPIRAL CABLE (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)


← Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter (from Nov 2010)Steering Pad Switch Circuit (from Nov 2010) →