2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter

Circuit diagnosis · Vehicles built from Nov 2010

DESCRIPTION

Speed signals are received from the combination meter assembly and used to cancel "Bluetooth" function operation.
The radio receiver assembly recognizes that the vehicle is being to driven and makes it impossible to connect or register a "Bluetooth" device while driving.

HINT:
  1. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.
  2. If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.


WIRING DIAGRAM

E222483E01

INSPECTION PROCEDURE


1. INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

  1. E126867E07
    Check the output waveform.
    1. Remove the combination meter assembly with the connector still connected (Click here).

    2. Connect an oscilloscope to terminal E13-14 (+S) and body ground.

    3. Turn the ignition switch ON.

    4. Turn the wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.

      Item
      Condition
      Measurement terminal
      E13-14 (+S) - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Driving at approx. 20 km/h (12 mph)
      Text in Illustration 
      *a
      Component with harness connected
      (Combination Meter Assembly)
      *b
      Turn wheel
      Result 
      Result
      Proceed to
      OK
      (for LHD)
      A
      OK
      (for RHD)
      B
      NG
      C



B
Go to step 4

C
GO TO METER / GAUGE SYSTEM (Click here)
A


2. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
  1. Disconnect the E43 radio receiver assembly and E59*1 or E60*2 junction connectors.*1: for 10 speaker with sub-woofer*2: for 6 speaker

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 10 speaker with sub-woofer 
    Tester Connection
    Condition
    Specified Condition
    E43-3 (SPD) - E60-7
    Always
    Below 1 Ω
    for 6 speaker 
    Tester Connection
    Condition
    Specified Condition
    E43-3 (SPD) - E59-6
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
  1. Disconnect the E59 junction connector and E13 combination meter connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E59-5 (SPD) - E13-14 (+S)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)

4. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
  1. Disconnect the E43 radio receiver assembly and E13 combination meter connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E43-3 (SPD) - E13-14 (+S)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)


← USB Audio System Recognition/Play Error (from Nov 2010)Steering Pad Switch Circuit (Jul 2007 – Oct 2010) →