P0418 Secondary Air Injection System Control "A" Circuit
Diagnostic trouble codes · Vehicles built from Aug 2014
DESCRIPTION
Refer to DTC P0412 (Click here).| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0418 |
All conditions are met for 3 seconds or more while idling immediately after the engine is started (2 trip detection logic):
|
|
| P0418 |
All conditions are met for 3 seconds or more while idling immediately after the engine is started (2 trip detection logic):
|
|
MONITOR DESCRIPTION
This DTC indicates an open or short circuit in the circuit containing the air pump assembly of the secondary air injection system. The air injection control driver performs diagnosis of the air pump assembly, emission control valve set and itself, and sends the results of this diagnosis to the ECM as a duty signal. When the ECM receives a signal indicating a malfunction in the air pump assembly, emission control valve set or air injection control driver, it illuminates the MIL and stores a DTC.CONFIRMATION DRIVING PATTERN
- NOTICE:
- This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.
- Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
- When Secondary performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.
- Start the engine and warm it up.
- Turn the ignition switch off.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch to ON.
- Turn the tester on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
- Turn the ignition switch off and wait for at least 30 seconds.
- Turn the ignition switch to ON and turn the tester on.
- Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.
- Start the engine after the tester initialization is finished.
- Perform the System Check operation by pressing Next.
- Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
- Enter the following menus: Powertrain / Engine and ECT / DTC.
- Read pending DTCs.
- HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- If a pending DTC is output, the system is malfunctioning.
- After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
- Input the DTC: P0418.
- Check the DTC judgment result.
Tester Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
- HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.
- If the judgment result shows NORMAL, the system is normal.
- DTC judgment completed
WIRING DIAGRAM
Refer to DTC P0412 (Click here).INSPECTION PROCEDURE
- NOTICE:
- After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
- HINT:
- By using the intelligent tester to perform the Secondary Air Injection Check operation in the System Check, the air fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- By using the intelligent tester to perform the Secondary Air Injection Check operation in the System Check, the air fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.
| 1. CHECK HARNESS AND CONNECTOR (AIR PUMP ASSEMBLY - AIR INJECTION CONTROL DRIVER, BATTERY AND BODY GROUND) |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Disconnect the A44 air pump assembly connector.
Disconnect the A46 air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A44-2 (+B) - A46-2 (VP)
Always
Below 1 Ω
A46-1 (BATT) - positive (+) battery terminal
Always
Below 1 Ω
A44-4 (GND) - Body ground
Always
Below 1 Ω
A44-2 (+B) or A46-2 (VP) - Body ground
Always
10 kΩ or higher
A46-1 (BATT) or positive (+) battery terminal - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 2. INSPECT AIR PUMP ASSEMBLY |
Inspect the air pump assembly (Click here).
|
|
||||
| OK | ||
| ||
| 3. REPLACE AIR PUMP ASSEMBLY |
Replace the air pump assembly (Click here).
| NEXT | |
| 4. CHECK WHETHER DTC OUTPUT RECURS (DTC P0418) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (if stored) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.
Start the engine after the tester initialization is finished.
Perform the System Check operation by pressing Next.
After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
- OK:
- No pending DTC is output.
Turn the ignition switch off.
- NOTICE:
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
- When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
|
|
||||
| OK | ||
| ||
