2011-2016 FJ Cruiser · Service Manual ENGINE

P0416 Secondary Air Injection System Switching Valve "B" Circuit Open

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

DESCRIPTION

The ECM operates the AI-VSV relay which causes the No. 2 emission control valve set to operate.
DTC No.
DTC Detection Condition
Trouble Area
P0416
Open or short in the AI-VSV relay circuit for 3 seconds (1 trip detection logic).
  1. Open or short in AI-VSV relay circuit
  2. AI-VSV relay
  3. ECM
P0417
Open or short in the AI-VSV relay circuit for 3 seconds (1 trip detection logic).
  1. Open or short in AI-VSV relay circuit
  2. AI-VSV relay
  3. ECM

MONITOR DESCRIPTION

These DTCs are designed to detect a malfunction in the AI-VSV relay circuit. When the system is normal, the battery voltage is applied to terminal AIR1 of the ECM while the AI-VSV relay is turned off, and the battery voltage is not applied to terminal AIR1 of the ECM while the AI-VSV relay is turned on. The ECM illuminates the MIL and stores a DTC when either one of the following conditions is detected.
  1. The battery voltage is not applied to terminal AIR1 while the AI-VSV relay is off.
  2. The battery voltage is applied to terminal AIR1 while the AI-VSV relay is on.

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.
  2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
  4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the tester on.
  6. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the tester on.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.
  10. Start the engine after the tester initialization is finished.
  11. Perform the System Check operation by pressing Next.
  12. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
  13. Enter the following menus: Powertrain / Engine and ECT / DTC.
  14. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  15. After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  16. Input the DTC: P0416 or P0417.
  17. Check the DTC judgment result.
    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.


WIRING DIAGRAM

A329620E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. By using the intelligent tester to perform the Secondary Air Injection Check operation in the System Check, the air fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.


1. INSPECT AI-VSV RELAY
A232574E01
  1. Remove the AI-VSV relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE AI-VSV RELAY
OK


2. CHECK TERMINAL VOLTAGE (POWER SOURCE OF AI-VSV RELAY)
  1. Remove the AI-VSV relay from the engine room relay block.

  1. A287417E01
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (AI-VSV relay holder) - Body ground
    Ignition switch ON
    11 to 14 V
    5 (AI-VSV relay holder) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    AI-VSV Relay Holder



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (ECM - AI-VSV RELAY))
  1. Remove the AI-VSV relay from the engine room relay block.

  1. Disconnect the B49 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (AI-VSV relay holder) - B49-21 (AIR1)
    Always
    Below 1 Ω
    2 (AI-VSV relay holder) or B49-21 (AIR1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0412 Secondary Air Injection System Switching Valve "A" Circuit (from Aug 2014)P0418 Secondary Air Injection System Control "A" Circuit (from Aug 2014) →