2011-2016 FJ Cruiser · Service Manual ENGINE

P0420 Catalyst System Efficiency Below Threshold (Bank 1)

Diagnostic trouble codes · Vehicles built Dec 2007 – Jul 2009

Also covers:

Versions by build date: Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014

MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.
The first sensor, the Air Fuel Ratio (A/F) sensor, sends pre-catalyst information to the ECM. The second sensor, the Heated Oxygen (HO2) sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the TWC, the ECM calculates the Oxygen Storage Capacity (OSC) of the TWC. This calculation is based on the voltage output of the HO2 sensor while performing active air- fuel ratio control, rather than the conventional detecting method, which uses the locus ratio.
The OSC value is an indication of the oxygen storage capacity of the TWC. When the vehicle is being driven with a warm engine, active air-fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air-fuel ratio to lean or rich levels. If a rich-lean cycle of the HO2 sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the HO2 sensor and the TWC.
The ECM uses the OSC value to determine the state of the TWC. If any deterioration has occurred, it illuminates the MIL and stores a DTC.
DTC No.
DTC Detection Condition
Trouble Area
P0420
OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic)
  1. Gas leak from exhaust system
  2. A/F sensor (bank 1 sensor 1)
  3. HO2 sensor (bank 1 sensor 2)
  4. Exhaust manifold (TWC)
P0430
OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic)
  1. Gas leak from exhaust system
  2. A/F sensor (bank 2 sensor 1)
  3. HO2 sensor (bank 2 sensor 2)
  4. Exhaust manifold (TWC)

HINT:
  1. Bank 1 refers to the bank that includes cylinder No. 1.
  2. Bank 2 refers to the bank that does not include cylinder No. 1.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.


CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation driving pattern will activate the catalyst monitor. This is very useful for verifying the completion of a repair.

A168054E18
  1. (a) Connect the intelligent tester to the DLC3.
  2. (b) Turn the ignition switch to ON.
  3. (c) Turn the tester ON.
  4. (d) Clear DTCs (if stored) (Click here).
  5. (e) Enter the following menus: Powertrain / Engine and ECT / Utility / Monitor Status.
  6. (f) Check that Catalyst is Incomplete.
  7. (g) Start the engine and warm it up.
  8. (h) Drive the vehicle at between 64 km/h and 113 km/h (40 mph and 70 mph) for at least 10 minutes.
  9. (i) Note the Result of Monitor Status. The Results will change to Complete as Catalyst monitor operates.
  10. (j) Enter the following menus: Powertrain / Engine and ECT / DTC / Pending and check if any DTCs (any pending DTCs) are output.

HINT:
If Catalyst does not change to Complete, and any pending DTCs fail to output, extend the driving time.


CONDITIONING FOR SENSOR TESTING


HINT:
Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the A/F and HO2 sensors. This is in order to activate the sensors sufficiently to obtain the appropriate inspection results.
A118003E38
  1. (a) Connect the intelligent tester to the DLC3.
  2. (b) Start the engine and warm it up with all the accessories switched OFF, until the engine coolant temperature stabilizes.
  3. (c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.
  4. (d) While running the engine at 3000 rpm for 2 seconds and 2000 rpm for 2 seconds, check the waveforms of the A/F and HO2 sensors using the tester.


HINT:
  1. If either of the voltage outputs of the Air Fuel Ratio (A/F) or Heated Oxygen (HO2) sensor does not fluctuate, or either of the sensors makes a noise, the sensor may be malfunctioning.
  2. If the voltage outputs of both the sensors remain lean or rich, the air-fuel ratio may be extremely lean or rich. In such cases, perform the following Control the Injection Volume for A/F sensor using the intelligent tester.
  3. If the Three-Way Catalytic Converter (TWC) has deteriorated, the HO2 sensor (located behind the TWC) voltage output fluctuates up and down frequently, even under normal driving conditions (active air-fuel ratio control is not performed).
A121610E01


INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.
  1. (1) Connect the intelligent tester to the DLC3.
  2. (2) Start the engine and turn the tester ON.
  3. (3) Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
  4. (4) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. (5) Perform the Control the Injection Volume for A/F sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
  6. (6) Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

    Standard:
    Tester Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS B1S1 or AFS B2S1
    (A/F)
    +25%
    Rich
    Less than 3.0 V
    AFS B1S1 or AFS B2S1
    (A/F)
    -12.5%
    Lean
    More than 3.35 V
    O2S B1S2 or O2S B2S2
    (HO2)
    +25%
    Rich
    More than 0.55 V
    O2S B1S2 or O2S B2S2
    (HO2)
    -12.5%
    Lean
    Less than 0.4 V

NOTICE:
The Air Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E01
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E01
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Fuel injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor / A/F Control System / AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2, then press View button.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 AND/OR P0430)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs and write them down.

    Result 
    Result
    Proceed to
    P0420 and/or P0430
    A
    P0420 and/or P0430 and other DTCs
    B

    HINT:
    If any DTCs other than P0420 or P0430 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (A/F CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

  1. Perform the Control the Injection Volume for A/F sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.

    HINT:
    1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


    Standard:
    Tester Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS B1S1 or AFS B2S1
    (A/F)
    +25%
    Rich
    Less than 3.0 V
    AFS B1S1 or AFS B2S1
    (A/F)
    -12.5%
    Lean
    More than 3.35 V
    O2S B1S2 or O2S B2S2
    (HO2)
    +25%
    Rich
    More than 0.55 V
    O2S B1S2 or O2S B2S2
    (HO2)
    -12.5%
    Lean
    Less than 0.4 V

    Result 
    Status
    AFS B1S1
    or
    AFS B2S1
    Status
    O2S B1S2
    or
    O2S B2S2
    A/F Condition and A/F and
    HO2 Sensor Condition
    Misfire
    Main Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    1. Three-Way Catalytic Converter (TWC)
    2. Gas leak from exhaust system
    A
    Lean
    Lean/Rich
    A/F sensor malfunction
    -
    1. A/F sensor
    B
    Rich
    Lean/Rich
    A/F sensor malfunction
    -
    1. A/F sensor
    Lean/Rich
    Lean
    HO2 sensor malfunction
    -
    1. HO2 sensor
    2. Gas leak from exhaust system
    C
    Lean/Rich
    Rich
    HO2 sensor malfunction
    -
    1. HO2 sensor
    2. Gas leak from exhaust system
    Lean
    Lean
    Actual air-fuel ratio lean
    May occur
    1. Extremely rich or lean actual air-fuel ratio
    2. Gas leak from exhaust system
    D
    Rich
    Rich
    Actual air-fuel ratio rich
    -
    1. Extremely rich or lean actual air-fuel ratio
    2. Gas leak from exhaust system
    Lean: During Control the Injection Volume for A/F sensor, the A/F sensor output voltage (AFS) is consistently more than 3.35 V, and the HO2 sensor output voltage (O2S) is consistently less than 0.4 V.Rich: During Control the Injection Volume for A/F sensor, the AFS is consistently less than 3.0 V, and the O2S is consistently more than 0.55 V.Lean/Rich: During Control the Injection Volume for A/F sensor of the Active Test, the output voltage of the HO2 sensor alternates correctly.



B
CHECK AND REPLACE AIR FUEL RATIO SENSOR (Click here)

C
Go to step 7

D
CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO, REPLACE FAULTY AREA AND GO TO NEXT STEP (Click here)
A


3. CHECK FOR EXHAUST GAS LEAK

OK:
No gas leak.



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK


4. CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)
  1. According to the DTCs output in Step 1 (Check Any Other DTCs Output), proceed to the next step, referring to the table below.

    Result 
    Result
    Proceed to
    P0420
    A
    P0430
    B
    P0420 and P0430
    A and B



A
Go to step 5

B
Go to step 6
5. REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY RH
  1. Replace the exhaust manifold sub-assembly RH (Click here).


NEXT

REPLACE FRONT EXHAUST PIPE ASSEMBLY (Click here)

6. REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY LH
  1. Replace the exhaust manifold sub-assembly LH (Click here).


NEXT

REPLACE NO. 2 FRONT EXHAUST PIPE ASSEMBLY (Click here)

7. CHECK FOR EXHAUST GAS LEAK

OK:
No gas leak.



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK

REPLACE OXYGEN SENSOR (Click here)


← P0418 Secondary Air Injection System Control "A" Circuit (from Aug 2014)P0420 Catalyst System Efficiency Below Threshold (Bank 1) (+ P0430) (Aug 2009 – Oct 2010) →