2011-2016 FJ Cruiser · Service Manual STEERING

INSTALLATION

Removal / installation · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014


1. INSTALL STEERING COLUMN ASSEMBLY

C133810
  1. Install the steering column assembly with the 4 nuts.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. Connect each of the connectors to the steering column assembly.

  1. Connect the wire harness clamps to the steering column assembly.

    CAUTION:
    Use a shop rag or piece of cloth to wipe any dirt off the installation plane and column body side.

    NOTICE:
    Be careful not to scratch or soil the installation plane of the steering column.


2. INSTALL NO.2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

F043317E01
  1. Align the matchmarks on the power steering gear and No. 2 steering intermediate shaft.

  1. Install the No. 2 steering intermediate shaft onto the steering gear box with bolt C.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf } for bolt C


3. INSTALL STEERING SLIDING YOKE
  1. Align the matchmarks on the steering column and steering sliding yoke.

  1. Install the steering sliding yoke onto the steering column assembly and slide it upward.

  1. Align the matchmarks on the No. 2 intermediate shaft sub-assembly and steering sliding yoke.

  1. Install the sliding yoke onto the No. 2 intermediate shaft sub-assembly with bolts A and B.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf } for bolt A, B


4. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the No. 1 engine under cover sub-assembly with the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


5. INSTALL FRONT WHEEL LH

6. INSTALL STEERING COLUMN HOLE COVER

F051329
  1. Install the steering column hole cover with the 4 clips.

    NOTICE:
    Be careful not to damage the dust seal of the steering column hole cover.


7. INSTALL NO.1 AIR DUCT

I102434
  1. Engage the 3 claws and install the air duct.


8. INSTALL LOWER INSTRUMENT PANEL LH

  1. B133864
    Install the lower instrument panel with the 4 <F> bolts.


9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH

  1. B133860
    Engage the 5 clips and claw and install the lower instrument panel finish panel.

  1. Install the 2 <F> bolts.


10. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.


11. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


12. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


13. INSTALL FRONT FLOOR FOOTREST

  1. B130589
    Engage the 2 studs and install the front floor footrest.


14. INSTALL NO.1 INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B133853
    Engage the 4 clips and 2 claws and install the instrument panel register.


15. INSTALL COMBINATION SWITCH ASSEMBLY

  1. C133809
    Install the 3 screws.

  1. Connect all connectors to the combination switch assembly.


16. INSTALL UPPER STEERING COLUMN COVER

  1. C133808
    Engage the claw and install the upper steering column cover.


17. INSTALL LOWER STEERING COLUMN COVER

  1. C133807
    Engage the 2 claws.

  1. Install the lower steering column cover with the 3 screws.


18. INSTALL STEERING WHEEL ASSEMBLY
  1. Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }


19. INSTALL STEERING PAD

  1. C128255E01
    Support the steering pad with one hand as shown in the illustration.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector.

  1. Confirm that the circumferencial groove of the "Torx" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

  1. Using "Torx" socket wrench (T30), tighten the 2 "Torx" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

    NOTICE:
    Tighten the 2 bolts while holding the steering pad to prevent it from moving upward.


20. INSTALL LOWER NO.3 STEERING WHEEL COVER

  1. C128195
    Install steering wheel cover lower No.3.


21. INSTALL LOWER NO.2 STEERING WHEEL COVER

  1. C128196
    Install steering wheel cover lower No.2.


22. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }


24. INSPECT SRS WARNING LIGHT
(Click here)
← REASSEMBLY (from Jul 2007)INSTALLATION (Nov 2010 – Jul 2012) →