2011-2016 FJ Cruiser · Service Manual STEERING

REASSEMBLY

Removal / installation · Vehicles built from Jul 2007


1. INSTALL KEY INTER LOCK SOLENOID (for Automatic Transmission)

  1. F043314
    Install the key inter lock solenoid onto the steering column bracket assembly upper with the 2 screws.


2. INSTALL IGNITION OR STARTER SWITCH ASSEMBLY

  1. F043313
    Install the ignition or starter switch assembly onto the steering column bracket assembly upper with the 2 screws.


3. INSTALL UN-LOCK WARNING SWITCH ASSEMBLY

  1. C090812
    Install the un-lock warning switch assembly onto the steering column bracket assembly upper.

  1. Connect the un-lock warning switch assembly connector to the ignition or starter switch assembly.


4. INSTALL IGNITION SWITCH LOCK CYLINDER ASSEMBLY
  1. Make sure that the ignition switch lock cylinder assembly is in the ACC position.

  1. Install the ignition switch lock cylinder assembly.


5. INSTALL TRANSPONDER KEY AMPLIFIER

  1. C090697
    Engage the 2 claws and install the transponder key amplifier onto the steering column upper with the switch bracket.


6. INSTALL STEERING MAIN SHAFT ASSEMBLY

  1. C090850
    Install the compression spring, bearing thrust collar and bearing onto the No. 1 main shaft.

  1. Temporarily install the steering column tube sub-assembly upper onto the No. 1 main shaft.

  1. H041541E01
    Secure the No. 1 main shaft with the steering column tube sub-assembly upper and SST in a vise.
    SST
    09316-60011   (09316-00051)

  1. H041542E01
    Using SST, compress the spring of the steering column tube sub-assembly upper.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09958-04011)

    NOTICE:
    Do not overtighten SST.

  1. H041543
    Using a snap ring expander, install a new snap ring onto the main shaft.

  1. C092889
    Assemble the No. 1 main shaft with the steering column tube sub-assembly upper and the No. 2 main shaft sub-assembly.

  1. C090875
    Using a 6 mm hexagon wrench, install the 2 tilt steering bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the main shaft with the steering column tube sub-assembly upper onto the column tube.

  1. F043307E01
    Using SST, install the tension spring.
    SST
    09921-00010  

  1. Install the turn signal bracket with the 2 bolts.

    Torque:
    5.7 N*m{ 58 kgf*cm , 50 in.*lbf }

  1. F043308E01
    Install the steering column protector with the 2 bolts.

    Torque:
    6 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. H041540E01
    Using SST, install the 2 tension springs.
    SST
    09921-00010  


7. INSTALL STEERING COLUMN UPPER CLAMP

  1. C090694
    Temporarily install the steering column bracket assembly upper and steering column upper clamp with 2 new tapered-head bolts.

  1. Tighten the 2 tapered-head bolts until the bolt heads break off.


8. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. F043315E01
    Align the matchmarks on the steering column assembly and the steering intermediate shaft assembly.

  1. Install the steering intermediate shaft assembly and thrust stopper onto the steering column assembly with the bolt.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

← DISASSEMBLY (from Jul 2007)INSTALLATION (Jul 2007 – Oct 2010) →