2011-2016 FJ Cruiser · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Aug 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

HINT:
Use the same procedure for both the RH and LH sides.


1. BOLTS, SCREWS AND NUTS TABLE

HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.


B271494E01

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


3. REMOVE FRONT DOOR SCUFF PLATE RH

  1. B130597
    Disengage the 14 claws and remove the front door scuff plate.


4. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


5. REMOVE FRONT FLOOR FOOTREST (for LHD)

  1. B130586
    Disengage the 4 claws and remove the front floor footrest.


6. REMOVE FOOTREST CLIP (for LHD)

  1. B130587
    Remove the 2 footrest clips.


7. REMOVE COWL SIDE TRIM BOARD RH

  1. B130599
    Remove the clip.

  1. Disengage the 2 claws and remove the cowl side trim board.


8. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


9. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip LH.


10. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip RH.


11. REMOVE ASSIST GRIP PLUG (w/ Assist Grip)

B175647E04

HINT:
Use the same procedure to remove all the assist grip plugs.

Text in Illustration 
*1
Protective Tape
*a
for RH Side
*b
for LH Side
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip plug.


12. REMOVE ASSIST GRIP ASSEMBLY (w/ Assist Grip)

B175648E04

HINT:
Use the same procedure to remove all the assist grips.

Text in Illustration 
*a
for RH Side
*b
for LH Side
  1. Remove the 2 screws and the assist grip.


13. REMOVE FRONT PILLAR GARNISH RH

  1. B267104
    Remove the 2 bolts.

  1. Disengage the claw and the guide and remove the roof side rail garnish.


14. REMOVE FRONT PILLAR GARNISH LH

HINT:
Use the same procedure as for the RH side.


15. REMOVE INSTRUMENT PANEL GARNISH LH

  1. B133886
    Remove screw <G>.

  1. Disengage the 3 clips and remove the instrument panel garnish.

    NOTICE:
    1. Pull the instrument panel garnish up at an angle of 45° to remove it.
    2. Do not damage the surface of the instrument panel when removing it.


16. REMOVE INSTRUMENT PANEL GARNISH RH

  1. B133887
    Remove screw <G>.

  1. Disengage the 3 clips and remove the instrument panel garnish.

    NOTICE:
    1. Pull the instrument panel garnish up at an angle of 45° to remove it.
    2. Do not damage the surface of the instrument panel when removing it.


17. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY

  1. B133888
    Remove the 2 screws.

  1. Disengage the 4 clips and remove the integration control panel assembly.

  1. Disconnect the 3 connectors.


18. REMOVE RADIO RECEIVER ASSEMBLY (w/ Radio Receiver)

  1. B130575
    Remove the 4 bolts.

  1. Disconnect the connectors and remove the radio receiver.


19. REMOVE RADIO TUNER OPENING COVER (w/o Radio Receiver)

  1. B267052
    Remove the 4 bolts and the radio tuner opening cover.


20. REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY

  1. B271473
    Disengage the 4 claws.

  1. Slide the parking brake hole cover toward the front of the vehicle, disengage the 2 guides and remove the parking brake hole cover.


21. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)

  1. B133893
    Remove the shift lever knob.


22. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD)

  1. B133895
    Remove the shift lever knob.


23. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY

  1. B271474
    Shift the shift lever into the N position.

  1. Disengage the 5 clips and 3 guides and remove the console upper rear panel.


24. REMOVE BOX BOTTOM MAT

  1. B133899
    Remove the box bottom mat.


25. REMOVE FRONT CONSOLE BOX

  1. B271475
    Remove the 4 <H> bolts.

  1. Disengage the 5 guides and remove the console box.


26. REMOVE CONSOLE UPPER PANEL NO. 1 GARNISH (for LHD)

  1. B271476
    Disengage claw and the clip.

  1. Slide the console upper panel garnish toward the rear of the vehicle, disengage the guide and remove the console upper panel garnish.


27. REMOVE CONSOLE UPPER PANEL NO. 1 GARNISH (for RHD)

  1. B267053
    Disengage claw and the 2 clips.

  1. Slide the console upper panel garnish toward the rear of the vehicle, disengage the guide and remove the console upper panel garnish.


28. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY

  1. B133852
    Remove the 2 clips and 2 <E> bolts.

  1. Disengage the 3 clips and 2 claws and remove the instrument lower cover.


29. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B133853
    Disengage the 4 clips and 2 claws and remove the instrument panel register.

    NOTICE:
    1. To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
    2. Pull the instrument panel register up diagonally to remove it.


30. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

  1. B133859
    Disengage the 3 claws and separate the hood lock control lever.


31. SEPARATE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for RHD)

  1. B267057
    Disengage the 3 claws and separate the fuel lid lock open lever.


32. REMOVE INSTRUMENT PANEL FINISH PLATE

  1. E149562E03
    Using a screwdriver with its tip wrapped in protective tape, remove the instrument panel finish plate.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Instrument Panel Finish Plate


33. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for LHD)

  1. B133860
    Remove the 2 <E> bolts.

  1. Disengage the 5 clips and claw and remove the lower instrument panel finish panel.


34. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for RHD)

  1. B267058
    Remove the 2 <E> bolts.

  1. Disengage the 8 clips and 4 guides.

  1. Disconnect the connectors and remove the lower instrument panel finish panel.


35. REMOVE LOWER INSTRUMENT PANEL LH (for LHD)

  1. B133864
    Remove the 4 <E> bolts and the lower instrument panel.


36. REMOVE INSTRUMENT CLUSTER FINISH PANEL (for LHD)

  1. B133861
    Disengage the 3 clips and the 4 claws and remove the instrument cluster finish panel.

  1. Disconnect the connectors.


37. REMOVE INSTRUMENT CLUSTER FINISH PANEL (for RHD)

  1. B267059
    Disengage the 8 clips and remove the instrument cluster finish panel.

  1. Disconnect the connectors.


38. REMOVE COMBINATION METER ASSEMBLY

  1. B133862
    Remove the 4 screws.

  1. B271477
    Disconnect the 2 connectors and clamp and remove the combination meter.


39. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

  1. B133854E02
    Disengage the claw and separate the glove compartment door stoppers from the glove compartment door.
    Text in Illustration 
    *1
    Stopper

  1. Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.

  1. B271478
    Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.


40. REMOVE INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY

  1. B133857
    Remove the screw <A>.

  1. Disengage the 2 clips and claw and remove the instrument panel lower finish panel.

  1. Separate the connectors from the instrument panel lower finish panel.


41. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B188205E02
    Apply protective tape, as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a thin-bladed screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the instrument panel hole cover.

  1. B188206
    Remove the bolt <E> and clip.

  1. Disengage the 4 clips and 2 claws and remove the instrument panel register.

    NOTICE:
    1. To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
    2. Pull the instrument panel register up diagonally to remove it.


42. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

  1. B133865
    Disengage the 4 clips and claw and remove the instrument panel speaker panel.


43. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

HINT:
Use the same procedure as for the RH side.


44. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY

  1. B135131
    Remove the 2 bolts and the front speaker.

  1. Disconnect the speaker connector.


45. REMOVE ASSIST GRIP RETAINER RH (w/ Assist Grip)

  1. B133881
    Remove the 2 bolts and remove the assist grip retainer.


46. REMOVE ASSIST GRIP RETAINER LH (w/ Assist Grip)

HINT:
Use the same procedure as for the RH side.


47. DISCONNECT PASSENGER AIRBAG CONNECTOR

  1. B133890E03
    Slide the slider and disconnect the passenger airbag connector.
    Text in Illustration 
    *1
    Slider


48. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)

  1. Disengage the clamps and disconnect the connectors.

    B133866E02

  1. Remove the 2 <B> bolts, 2 <D> bolts, 7 <C> bolts and nut <F> and remove the instrument panel.


49. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)

  1. Disengage the clamps and disconnect the connectors.

    B267066E01

  1. Remove the 2 <B> bolts, 2 <D> bolts, 2 <E> bolts, 7 <C> bolts and nut <F> and remove the instrument panel.


50. REMOVE METER COVER

  1. B133867
    Disengage the 6 clips and remove the meter cover.


51. REMOVE ACCESSORY METER ASSEMBLY

  1. B133868
    Remove the 2 nuts and the accessory meter.


52. REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY (for LHD)

  1. B133870
    Remove the 2 <G> screws.

  1. Disengage the 4 clips and 2 claws and remove the instrument panel box door.


53. REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY (for RHD)

  1. B267067
    Remove the 2 <G> screws.

  1. Disengage the 5 clips and remove the instrument panel box door.


54. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY

  1. B133878
    Disengage the claw and remove the glove compartment door stopper.


55. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B133871
    Remove the 3 <A> screws.

  1. Disengage the 2 clips and 2 claws and remove the instrument cluster finish panel.


56. REMOVE INSTRUMENT CLUSTER CENTER FINISH PANEL SUB-ASSEMBLY

  1. B133872
    Remove the 2 <A> screws.

  1. Disengage the 4 claws and remove the instrument cluster center finish panel.


57. REMOVE INSTRUMENT CLUSTER LOWER CENTER FINISH PANEL SUB-ASSEMBLY

  1. B133880
    Remove the 3 <A> screws.

  1. Disengage the 2 clips and 3 claws and remove the instrument cluster lower center finish panel.


58. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT

  1. B133874
    Remove the screw <A>.

  1. Disengage the 2 claws and remove the side defroster nozzle duct.


59. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT

  1. B133873
    Remove the screw <A>.

  1. Disengage the 2 claws and remove the side defroster nozzle duct.


60. REMOVE DEFROSTER NOZZLE ASSEMBLY

  1. B133875
    Remove the 5 <A> screws.

  1. Disengage the 9 claws and remove the defroster nozzle.


61. REMOVE NO. 3 HEATER TO REGISTER DUCT

  1. B133876
    Remove the 2 <A> screws and the heater to register duct.


62. REMOVE NO. 2 INSTRUMENT PANEL WIRE (for LHD)

  1. Disengage the 16 clamps and remove the instrument panel wire.

    B271480


63. REMOVE NO. 2 INSTRUMENT PANEL WIRE (for RHD)

  1. Disengage the 15 clamps and remove the instrument panel wire.

    B267076


64. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY

  1. C128213
    Remove the 2 screws.

  1. C128214E01
    Using a screwdriver (with its tip wrapped in protective tape), disengage the 5 hooks from the instrument panel and turn the front passenger airbag assembly in the direction indicated by the arrow shown in the illustration.

  1. Disengage the 5 hooks and remove the front passenger airbag assembly from the instrument panel.


65. REMOVE INSTRUMENT PANEL CENTER BRACKET SUB-ASSEMBLY

  1. B133877
    Remove the 2 <A> screws and the instrument panel center bracket.


66. REMOVE ACCESSORY METER BRACKET

  1. B133882
    Remove the 2 clips and the accessory meter bracket.


67. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY RH

  1. B133879
    Disengage the 2 clips and remove the lower instrument panel.


68. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


69. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

  1. B133889
    Disengage the 3 claws and remove the instrument panel finish panel end.


70. REMOVE INSTRUMENT PANEL PLATE RH

  1. B271479
    Remove the 2 screws and the instrument panel plate RH.


71. REMOVE NO. 2 INSTRUMENT PANEL CUSHION

  1. B267082
    Remove the No. 2 instrument panel cushion.


72. REMOVE GLOVE COMPARTMENT DOOR CHECK CUSHION (for RHD)

  1. B267080
    Remove the 3 glove compartment door check cushions.

← REMOVAL (Nov 2010 – Jul 2012)INSTALLATION (Jul 2007 – Oct 2010) →