2011-2016 FJ Cruiser · Service Manual DRIVE LINE

REASSEMBLY

Removal / installation · Vehicles built from Aug 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


1. INSTALL DIFFERENTIAL CASE ASSEMBLY

C216548
  1. Install the rear differential side gear thrust washer onto the rear differential side gear.

  1. Install the rear differential pinion thrust washer and rear differential pinion onto the rear differential spider.

  1. Fix the differential case RH.

  1. ZK09096
    Install the rear differential side gear and rear differential spider onto the differential case RH.

  1. ZK09097
    Using a dial indicator, measure the differential case RH side backlash while holding the pinion toward the case.

    Backlash:
    0.05 to 0.20 mm (0.002 to 0.008 in.)

  1. Remove the rear differential spider from the differential case RH.

  1. ZK09098
    Install the rear differential side gear and rear differential spider onto the differential case LH.

  1. Using a dial indicator, measure the differential case LH side backlash while holding the pinion toward the case.

    Backlash:
    0.05 to 0.20 mm (0.002 to 0.008 in.)

    If the backlash is not within the specification, install 2 side gear thrust washers of a different thickness.

    Thrust washer thickness:
    Thickness mm (in.)
    Thickness mm (in.)
    0.88 to 0.92 (0.0346 to 0.0362)
    1.18 to 1.22 (0.0465 to 0.0480)
    0.98 to 1.02 (0.0386 to 0.0402)
    1.28 to 1.32 (0.0504 to 0.0520)
    1.08 to 1.12 (0.0425 to 0.0441)
    -

  1. C089323E07
    Align the matchmarks and assemble the RH and LH cases.
    Text in Illustration 
    *a
    Matchmark

  1. Using a plastic hammer, install the differential case.

  1. Install the 8 bolts.

    Torque:
    47 N*m{ 480 kgf*cm , 35 ft.*lbf }


2. INSTALL DIFFERENTIAL RING GEAR

SA01143E02
  1. Clean the contact surfaces of the differential case and ring gear.

  1. Heat the ring gear to approximately 100 °C (212 °F) in boiling water.

  1. Carefully take the ring gear out of the boiling water.

  1. After the moisture on the ring gear has completely evaporated, quickly install the ring gear onto the differential case.

  1. C216547E02
    Align the matchmarks on the ring gear with those of the differential case.
    Text in Illustration 
    *a
    Matchmark

  1. After the ring gear cools down sufficiently, apply adhesive to the 12 bolts and install them.

    Adhesive:
    Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent.

    Torque:
    97 N*m{ 985 kgf*cm , 71 ft.*lbf }


3. INSTALL REAR DIFFERENTIAL CASE BEARING

C216550E01
  1. Using SST and a press, install the bearing onto the differential case.

    SST
    09308-14010  
    09950-60010   (09951-00490)


4. INSPECT DIFFERENTIAL RING GEAR RUNOUT

C217282
  1. Install the differential case onto the carrier, and install the 2 adjusting nuts so that there is no play in the bearing.

  1. Install the 2 bearing caps with the 4 bolts.

    Torque:
    103 N*m{ 1049 kgf*cm , 76 ft.*lbf }

  1. Using a dial indicator, measure the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

  1. Remove the 2 bearing caps, 2 adjusting nuts and differential case.


5. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

C197664E01
  1. Using SST and a press, install the tapered roller bearing onto the carrier.

    SST
    09308-14010  
    09309-14040  


6. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

C217284E01
  1. Install the plate washer onto the carrier.

    HINT:
    First fit a washer with the same thickness as the removed washer, and then check the tooth contact pattern. Replace the washer with one of a different thickness if necessary.

  1. Using SST and a press, install the tapered roller bearing onto the carrier.

    SST
    09950-70010   (09951-07200)
    09255-10012  


7. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

SA03102E03
  1. Using SST and a press, install the tapered roller bearing onto the drive pinion.

    SST
    09506-30012  


8. ADJUST DIFFERENTIAL DRIVE PINION PRELOAD

C028218
  1. Install the drive pinion, rear drive pinion tapered roller bearing and rear differential drive oil slinger.

    HINT:
    Assemble the spacer and oil seal after adjusting the gear contact pattern.

  1. F052182E01
    Using SST, install the drive pinion companion flange.

  1. Coat the threads of the nut with hypoid gear oil LSD.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. ZK09978E01
    Using SST to hold the drive pinion companion flange, tighten the nut.

    Torque:
    457 N*m{ 4660 kgf*cm , 337 ft.*lbf } or less

    SST
    09330-00021  

    NOTICE:
    1. As there is no spacer, tighten the nut a little at a time, being careful not to overtighten it.
    2. Apply hypoid gear oil to the nut.

  1. C003092
    Using a torque wrench, measure the preload.

    Preload (at starting):
    Bearing
    Standard
    New bearing
    0.83 to 2.18 N*m (8.64 to 22.2 kgf*cm, 7.35 to 19.3 in.*lbf)
    Used bearing
    0.88 to 1.98 N*m (8.97 to 20.2 kgf*cm, 7.79 to 17.5 in.*lbf)

    NOTICE:
    For a more accurate measurement, rotate the bearing forward and backward several times before measuring.


9. INSTALL DIFFERENTIAL CASE ASSEMBLY

C217285
  1. Place the 2 bearing outer races on their corresponding bearings.

    HINT:
    Make sure the right and left races are not interchanged.


10. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT

C217286
  1. Install the 2 adjusting nuts into the carrier, making sure the nuts are threaded properly.


11. INSPECT AND ADJUST DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH

C217292E01
Text in Illustration 
*1
Matchmark
  1. Align the matchmarks on the cap and carrier.

  1. Install the right and left bearing caps with the 4 bolts.

    Torque:
    103 N*m{ 1049 kgf*cm , 76 ft.*lbf }

    HINT:
    If the bearing cap does not fit tightly onto the carrier, the adjusting nuts are not threaded properly.
    Reinstall the adjusting nuts if necessary.

  1. C217288E01
    Tighten the 4 bearing cap bolts to the specified torque, then loosen them to the point where the adjusting nuts can be turned by SST.
    Text in Illustration 
    *a
    LH Side

    Torque:
    103 N*m{ 1049 kgf*cm , 76 ft.*lbf }

  1. Using the SST, tighten the adjusting nut on the ring gear side until the ring has a backlash of about 0.2 mm (0.008 in.).

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. C217287E01
    While turning the ring gear, use the SST to fully tighten the adjusting nut on the drive pinion side.
    Text in Illustration 
    *a
    RH Side
    After the bearings have settled, loosen the adjusting nut on the drive pinion side.

  1. Using SST, torque the adjusting nut 1 to 1.5 notches from the 0 preload position.

    SST
    09504-00011  

  1. C217289E01
    Using a dial indicator, adjust the ring gear backlash until it is within the specification.

    Backlash:
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)

    HINT:
    1. The backlash is adjusted by turning the left and right adjusting nuts an equal amount. For example, loosen the nut on the right side one notch and loosen the nut on the left side one notch.
    2. Perform the measurement at 3 or more positions around the circumference of the ring gear.

  1. C217292E01
    Torque the bearing cap bolts.
    Text in Illustration 
    *1
    Matchmark

    Torque:
    103 N*m{ 1049 kgf*cm , 76 ft.*lbf }


12. INSPECT TOTAL PRELOAD

C003092
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Total preload (at starting):
    Drive pinion preload plus 0.20 to 0.40 N*m (2.0 to 4.1 kgf*cm, 1.8 to 3.5 in.*lbf)

    If necessary, disassemble and inspect the differential.


13. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

C014071
  1. Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.

  1. Hold the companion flange firmly and rotate the ring gear in both directions.

  1. Inspect the tooth contact pattern.

    1. C113184E01

    2. C217047E01
      Text in Illustration 
      *1
      Plate Washer
      *2
      Rear Drive Pinion Rear Tapered Roller Bearing (Outer)
      If the teeth are not engaged properly, use the following chart to select an appropriate washer for correction.
      Plate Washer Thickness 
      Thickness mm (in.)
      Thickness mm (in.)
      1.845 to 1.855 (0.0726 to 0.0730)
      2.085 to 2.095 (0.0821 to 0.0825)
      1.855 to 1.865 (0.0730 to 0.0734)
      2.095 to 2.105 (0.0825 to 0.0829)
      1.865 to 1.875 (0.0734 to 0.0738)
      2.105 to 2.115 (0.0829 to 0.0833)
      1.875 to 1.885 (0.0738 to 0.0742)
      2.115 to 2.125 (0.0833 to 0.0837)
      1.885 to 1.895 (0.0742 to 0.0746)
      2.125 to 2.135 (0.0837 to 0.0841)
      1.895 to 1.905 (0.0746 to 0.0750)
      2.135 to 2.145 (0.0841 to 0.0844)
      1.905 to 1.915 (0.0750 to 0.0754)
      2.145 to 2.155 (0.0844 to 0.0848)
      1.915 to 1.925 (0.0754 to 0.0758)
      2.155 to 2.165 (0.0848 to 0.0852)
      1.925 to 1.935 (0.0758 to 0.0762)
      2.165 to 2.175 (0.0852 to 0.0856)
      1.935 to 1.945 (0.0762 to 0.0766)
      2.175 to 2.185 (0.0856 to 0.0860)
      1.945 to 1.955 (0.0766 to 0.0770)
      2.185 to 2.195 (0.0860 to 0.0864)
      1.955 to 1.965 (0.0770 to 0.0774)
      2.195 to 2.205 (0.0864 to 0.0868)
      1.965 to 1.975 (0.0774 to 0.0778)
      2.205 to 2.215 (0.0868 to 0.0872)
      1.975 to 1.985 (0.0778 to 0.0781)
      2.215 to 2.225 (0.0872 to 0.0876)
      1.985 to 1.995 (0.0781 to 0.0785)
      2.225 to 2.235 (0.0876 to 0.0880)
      1.995 to 2.005 (0.0785 to 0.0789)
      2.235 to 2.245 (0.0880 to 0.0884)
      2.005 to 2.015 (0.0789 to 0.0793)
      2.245 to 2.255 (0.0884 to 0.0888)
      2.015 to 2.025 (0.0793 to 0.0797)
      2.255 to 2.265 (0.0888 to 0.0892)
      2.025 to 2.035 (0.0797 to 0.0801)
      2.265 to 2.275 (0.0892 to 0.0896)
      2.035 to 2.045 (0.0801 to 0.0805)
      2.275 to 2.285 (0.0896 to 0.0900)
      2.045 to 2.055 (0.0805 to 0.0809)
      2.285 to 2.295 (0.0900 to 0.0904)
      2.055 to 5.065 (0.0809 to 0.0813)
      2.295 to 2.305 (0.0904 to 0.0907)
      2.065 to 2.075 (0.0813 to 0.0817)
      2.305 to 2.315 (0.0907 to 0.0911)
      2.075 to 2.085 (0.0817 to 0.0821)
      -


14. REMOVE REAR DRIVE PINION NUT

SA02349E05
  1. Using SST to hold the drive pinion companion flange, remove the nut.

    SST
    09330-00021  


15. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

F052175E03
  1. Using SST, remove the drive pinion companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)


16. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

17. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

18. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

C093601
  1. Install a new bearing spacer onto the drive pinion.


19. INSTALL DIFFERENTIAL OIL STORAGE RING

  1. C216551E01
    Using SST, tap in a new oil storage ring.
    SST
    09308-14010  


20. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

21. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

22. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

C217046E01
  1. Apply MP grease to the oil seal lip.

  1. Using SST and a hammer, install a new carrier oil seal.

    SST
    09214-76011  

    Oil seal drive in depth:
    -0.3 to 0.3 mm (-0.012 to 0.012 in.)


23. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR

F052182E01
  1. Using SST, install the drive pinion companion flange onto the drive pinion.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

  1. ZK09978E01
    Coat the threads of a new nut with hypoid gear oil LSD.

  1. Using SST to hold the flange, tighten the nut.

    SST
    09330-00021  

    Torque:
    457 N*m{ 4660 kgf*cm , 337 ft.*lbf } or less


24. INSPECT DRIVE PINION PRELOAD

SA02352
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Preload (at starting):
    Bearing
    Standard
    New bearing
    0.83 to 2.18 N*m (8.64 to 22.2 kgf*cm, 7.35 to 19.3 in.*lbf)
    Used bearing
    0.88 to 1.98 N*m (8.97 to 20.2 kgf*cm, 7.79 to 17.5 in.*lbf)

    If the preload is greater than the specification, replace the bearing spacer.
    If the preload is less than the specification, retighten the nut to 13 N*m (130 kgf*cm, 9 ft*lbf) of torque at a time until the specified preload is reached.

    Torque:
    457 N*m{ 4660 kgf*cm , 337 ft.*lbf } or less

    If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repeat the preload adjusting procedure.

    HINT:
    Do not loosen the pinion nut to reduce the preload.


25. INSPECT TOTAL PRELOAD

SA02352
  1. Using a torque wrench, measure the preload.

    Total preload (at starting):
    Drive pinion preload plus 0.20 to 0.40 N*m (2.0 to 4.1 kgf*cm, 1.8 to 3.5 in.*lbf)

    If necessary, disassemble and inspect the differential.


26. INSPECT DIFFERENTIAL RING GEAR BACKLASH

C217283
  1. Using a dial indicator, check the backlash of the ring gear.

    Backlash:
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)

    If the backlash is not within the specification, adjust or repair the side bearing preload as necessary.

    HINT:
    Perform the measurements at 3 or more positions around the circumference of the ring gear.


27. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR

F001237E03
  1. Using a dial indicator, measure the runout of the drive pinion companion flange vertically and horizontally.

    Runout
    Maximum
    Vertical runout
    0.14 mm (0.0055 in.)
    Lateral runout
    0.14 mm (0.0055 in.)
    If the runouts are not within the specifications, replace the companion flange.


28. INSTALL REAR DRIVE PINION NUT

ZK07449
  1. Using a chisel and hammer, stake the drive pinion nut.


29. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

C217290
  1. Install 2 new adjusting nut locks onto the bearing caps with the 2 bolts.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. After tightening the bolts, bend the nut locks.


30. INSTALL REAR DIFFERENTIAL LOCK SHIFT FORK

F052195E03
Text in Illustration 
*1
Holes
*2
Groove
  1. Apply MP grease onto the outer circuit of the shaft.

  1. Install the fork shaft to align the hole of the shift fork with that of the shift fork shaft.

  1. Z015179E04
    Remove any FIPG material and be careful not to drop the oil shaft retainer.

  1. Apply FIPG to the carrier, as shown in the illustration.

    Text in Illustration 
    *a
    FIPG Width Approx. 1 to 2 mm (0.0394 to 0.0787 in.)

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent

    HINT:
    Install the shaft retainer within 10 minutes of applying FIPG.

  1. F052198E03
    Clean the threads of the bolts and retainer bolts holes with toluene or trichloroethylene.
    Text in Illustration 
    *1
    Adhesive

  1. Apply adhesive to 2 or 3 threads of each mount bolt end.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. Tighten the shaft retainer with the 2 bolts.

    Torque:
    23 N*m{ 237 kgf*cm , 17 ft.*lbf }

  1. G020271
    Using a 5 mm pin punch and hammer, install the slotted spring pin into the shift fork.

    Torque:
    22 N*m{ 220 kgf*cm , 16 ft.*lbf }

  1. F052196E02
    Push the differential lock sleeve in deeply and hold it in position.
    Text in Illustration 
    *1
    Lock

  1. F052197E03
    Install the ball, spring and spring seat.
    Text in Illustration 
    *1
    Adhesive

  1. Clean the threads of 2 plugs and plug holes with toluene or trichloroethylene.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent

  1. Using a 6 mm hexagon wrench, install and tighten the screw plugs.

    Torque:
    23 N*m{ 237 kgf*cm , 17 ft.*lbf }


31. INSTALL NO.1 TRANSFER INDICATOR SWITCH

G020279
  1. Install the indicator switch with a new gasket.

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }


32. INSPECT REAR DIFFERENTIAL LOCK SLEEVE

G020285
  1. Measure the distances between the sleeve and tip of the differential case when the differential is free and locked, respectively.

    Standard distance:
    LOCKED: 17.44 to 18.86 mm (0.6866 to 0.7425 in.)
    FREE: 32.40 to 33.90 mm (1.2756 to 1.3346 in.)


33. INSTALL DIFFERENTIAL LOCK SHIFT ACTUATOR

R008153E04
Text in Illustration 
*1
Shift Fork
*2
Actuator Installation Hole
*a
Outside
  1. Check that the outermost rack tooth of the shift fork is approximately above the center line of the actuator installation hole.

  1. F052172E04
    Ensure that the matchmarks on the pinion of the actuator are in the range between 0 and 5 degrees clockwise above the center line of the actuator.
    Text in Illustration 
    *1
    Matchmark
    *2
    Groove

    NOTICE:
    1. If the matchmarks are not within this range, rotate the pinion.
    2. Do not supply the battery positive voltage directly between the terminals.
    3. If the matchmarks come to the limit of rotation, do not apply the electric current.

  1. Install a new O-ring onto the actuator.

  1. Apply a light coat of gear oil to the O-ring.

  1. Apply MP grease to the gear part.

  1. G020288E02
    Ensure that the outermost rack tooth of the shift fork fits the matchmarks on the pinion of the actuator.
    Text in Illustration 
    *1
    Knock Pin

  1. Install the actuator so that the long hole on the actuator side fits into the knock pin on the carrier side.

    HINT:
    Do not damage the O-ring of the actuator.

  1. Align the actuator with the long hole and rotate the actuator counterclockwise when the knock pin is set in the left-hand side.

  1. Install and tighten the bolts.

    Torque:
    27 N*m{ 270 kgf*cm , 20 ft.*lbf }

← REASSEMBLY (Jul 2007 – Jul 2009)INSTALLATION (Jul 2007 – Jul 2009) →