2011-2016 FJ Cruiser · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010


1. REMOVE SHIFT LEVER ASSEMBLY (for Automatic Transmission)
(Click here)

2. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Transfer)

3. REMOVE SHIFT LEVER BOOT ASSEMBLY

C135793
  1. Remove the 4 screws and shift lever boot.


4. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY

C113710E04
  1. Using needle-nose pliers, remove the snap ring and pull out the shift lever from the shift lever retainer.


5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

6. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

7. REMOVE REAR ENGINE UNDER COVER ASSEMBLY

8. DISCONNECT OXYGEN SENSOR

9. REMOVE NO. 2 EXHAUST FRONT PIPE ASSEMBLY

  1. A129939
    Remove the 2 bolts, then remove the exhaust pipe stopper bracket. (for 4WD)

  1. A129938
    Remove the 2 bolts and 2 nuts and separate the exhaust pipe support, then remove the No. 2 front exhaust pipe.


10. REMOVE FRONT EXHAUST PIPE ASSEMBLY

  1. A128851
    Remove the 2 nuts, then remove the front exhaust pipe.

  1. Remove the front exhaust pipe gasket.


11. REMOVE PROPELLER SHAFT HEAT INSULATOR

C133778
  1. Remove the 2 bolts and propeller shaft heat insulator.


12. REMOVE FRONT PROPELLER SHAFT ASSEMBLY

C098708E04
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4bolts and 4 washers.

  1. C098709E03
    Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and the propeller shaft assembly.


13. REMOVE PROPELLER SHAFT ASSEMBLY

C098699E02
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts and 4 washers.

  1. C098700E02
    Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts, 4 washers and the propeller shaft assembly.


14. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


15. REMOVE MANIFOLD STAY

F050360
  1. Remove the 3 bolts and the manifold stay.


16. REMOVE NO. 2 MANIFOLD STAY

F050356
  1. Remove the 3 bolts and the No. 2 manifold stay.


17. DISCONNECT OIL COOLER TUBE

F051602
  1. Remove the 3 bolts and 2 clamps.

  1. F050350
    Using SST, disconnect the No. 1 oil cooler inlet tube.
    SST
    09023-12701  

  1. Using SST, disconnect the No. 1 oil cooler outlet tube.

    SST
    09023-12701  


18. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

F050351
  1. Remove the nut and disconnect the transmission control cable.

  1. Remove the 2 bolts and disconnect the transmission control cable.


19. SUPPORT AUTOMATIC TRANSMISSION WITH TRANSFER

C111233
  1. Support the automatic transmission assembly with a transmission jack.


20. REMOVE FRONT SUSPENSION MEMBER BRACKET LH

C129541
  1. Remove the 4 bolts and the front suspension member bracket LH.


21. REMOVE FRONT SUSPENSION MEMBER BRACKET RH

C129542
  1. Remove the 4 bolts and the front suspension member bracket RH.


22. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

C133780
  1. Remove the 4 bolts on the No. 3 frame crossmember sub-assembly.

  1. Remove the 4 nuts, 4 bolts and the No. 3 frame crossmember sub-assembly.


23. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

C133779
  1. Remove the 4 bolts and engine mounting insulator rear from the automatic transmission.


24. DISCONNECT CONNECTOR
  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the transmission wire connector.

  1. Disconnect the 2 speed sensor connectors.

  1. Disconnect the 3 indicator switch connectors.


25. DISCONNECT WIRE HARNESS

26. REMOVE STARTER ASSEMBLY

  1. A128855
    Disconnect the terminal 50 connector from the starter assembly.

  1. Remove the nut, then disconnect the wire harness from the terminal 30.

  1. A128856
    Remove the 2 bolts, then remove the starter assembly.


27. REMOVE FLYWHEEL HOUSING SIDE COVER

F050352
  1. Remove the flywheel housing side cover from the cylinder block.


28. REMOVE AUTOMATIC TRANSMISSION WITH TRANSFER

F050354
  1. Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley nut with a wrench and remove the 6 bolts.

  1. F051601
    Remove the 9 bolts.

  1. Separate and remove the automatic transmission.


29. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY

30. REMOVE TRANSFER ASSEMBLY
  1. Remove the 8 bolts and 2 clamps.

  1. Remove the transfer from the transmission.

← COMPONENTS (from Jul 2007)REMOVAL (from Nov 2010) →