REMOVAL
Removal / installation · Vehicles built from Nov 2010
Versions by build date: Jul 2007 – Oct 2010 from Nov 2010
| 1.
REMOVE SHIFT LEVER ASSEMBLY (for Automatic Transmission) |
 |
(Click here)
| 2.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Transfer) |
|
| 3.
REMOVE SHIFT LEVER BOOT ASSEMBLY |
 |
Remove the 4 screws and shift lever boot.
| 4.
REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY |
 |
Using needle-nose pliers, remove the snap ring and pull out the shift lever from the shift lever retainer.
| 5.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
|
| 6.
REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
|
| 7.
REMOVE REAR ENGINE UNDER COVER ASSEMBLY |
|
| 8.
DISCONNECT OXYGEN SENSOR |
|
| 9.
REMOVE NO. 2 EXHAUST FRONT PIPE ASSEMBLY
|
 |
- Remove the 2 bolts and 2 nuts and separate the exhaust pipe support, then remove the No. 2 front exhaust pipe.
Remove the front exhaust pipe gasket.
| 10.
REMOVE FRONT EXHAUST PIPE ASSEMBLY
|
 |
- Remove the 2 nuts, then remove the front exhaust pipe.
Remove the front exhaust pipe gasket.
| 11.
REMOVE PROPELLER SHAFT HEAT INSULATOR |
 |
Remove the 2 bolts and propeller shaft heat insulator.
| 12.
REMOVE FRONT PROPELLER SHAFT ASSEMBLY
|
 |
Place matchmarks on the propeller shaft flange and differential flange.
Remove the 4 nuts, 4bolts and 4 washers.
- Place matchmarks on the propeller shaft flange and transfer flange.
Remove the 4 nuts, 4 washers and the propeller shaft assembly.
| 13.
REMOVE PROPELLER SHAFT ASSEMBLY
|
 |
Place matchmarks on the propeller shaft flange and transfer flange.
Remove the 4 nuts and 4 washers.
- Place matchmarks on the propeller shaft flange and differential flange.
Remove the 4 nuts, 4 bolts, 4 washers and the propeller shaft assembly.
| 14.
DRAIN AUTOMATIC TRANSMISSION FLUID |
 |
Remove the drain plug and gasket, and drain ATF.
Install a new gasket and drain plug.
-
Torque:
- 20 N*m{
204 kgf*cm
, 15 ft.*lbf
}
| 15.
REMOVE MANIFOLD STAY |
 |
Remove the 3 bolts and the manifold stay.
| 16.
REMOVE NO. 2 MANIFOLD STAY |
 |
Remove the 3 bolts and the No. 2 manifold stay.
| 17.
DISCONNECT OIL COOLER TUBE |
 |
Remove the 3 bolts and 2 clamps.
- Using SST, disconnect the No. 1 oil cooler inlet tube.
- SST
- 09023-12701
Using SST, disconnect the No. 1 oil cooler outlet tube.
- SST
- 09023-12701
| 18.
DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
 |
Remove the nut and disconnect the transmission control cable.
Remove the 2 bolts and disconnect the transmission control cable.
| 19.
SUPPORT AUTOMATIC TRANSMISSION WITH TRANSFER |
 |
Support the automatic transmission assembly with a transmission jack.
| 20.
REMOVE FRONT SUSPENSION MEMBER BRACKET LH |
 |
Remove the 4 bolts and the front suspension member bracket LH.
| 21.
REMOVE FRONT SUSPENSION MEMBER BRACKET RH |
 |
Remove the 4 bolts and the front suspension member bracket RH.
| 22.
REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
 |
Remove the 4 bolts on the No. 3 frame crossmember sub-assembly.
Remove the 4 nuts, 4 bolts and the No. 3 frame crossmember sub-assembly.
| 23.
REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR |
 |
Remove the 4 bolts and engine mounting insulator rear from the automatic transmission.
| 24.
DISCONNECT CONNECTOR |
 |
Disconnect the park/neutral position switch connector.
Disconnect the transmission wire connector.
Disconnect the 2 speed sensor connectors.
Disconnect the 3 indicator switch connectors.
| 25.
DISCONNECT WIRE HARNESS |
|
| 26.
REMOVE STARTER ASSEMBLY
|
 |
- Remove the bolt and ground wire.
Disconnect the starter connector.
Open the terminal cap.
Remove the nut and bolt, and then disconnect the starter wire.
- Remove the 2 bolts and starter.
| 27.
REMOVE FLYWHEEL HOUSING SIDE COVER |
 |
Remove the flywheel housing side cover from the cylinder block.
| 28.
REMOVE AUTOMATIC TRANSMISSION WITH TRANSFER |
 |
Turn the crankshaft to gain access to each bolt.
Hold the crankshaft pulley nut with a wrench and remove the 6 bolts.
- Remove the 9 bolts.
Separate and remove the automatic transmission.
| 29.
REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY |
|
| 30.
REMOVE TRANSFER ASSEMBLY
|
 |
Remove the 8 bolts and 2 clamps.
Remove the transfer from the transmission.