INSTALLATION
Removal / installation · Vehicles built Jul 2007 – Oct 2010
Versions by build date: Jul 2007 – Oct 2010 from Nov 2010
| 1. INSTALL FRONT DRIVE SHAFT |
![]() ![]() |
Coat the spline of the inboard joint shaft with ATF.
Align the shaft splines and install the drive shaft with a brass bar and hammer.
- NOTICE:
- Set the snap ring with the opening side facing downward.
- Do not damage the oil seal.
- Set the snap ring with the opening side facing downward.
- HINT:
- Whether the inboard joint shaft is in contact with the pinion shaft or not can be confirmed from the sound or feeling when driving it.
| 2. INSTALL FRONT LOWER BALL JOINT ATTACHMENT |
Install the front lower ball joint attachment with the 2 bolts.
- Torque:
- 160 N*m{ 1631 kgf*cm , 118 ft.*lbf }
| 3. INSTALL TIE ROD END SUB-ASSEMBLY |
![]() ![]() |
Install the tie rod end onto the steering knuckle.
Install the nut.
- Torque:
- 91 N*m{ 928 kgf*cm , 67 ft.*lbf }
Install a new cotter pin.
- NOTICE:
- If the holes in the cotter pin are not aligned, tighten the nut an additional 60°.
| 4. INSTALL FRONT AXLE HUB NUT |
Install the hub nut.
- Torque:
- 235 N*m{ 2396 kgf*cm , 174 ft.*lbf }
Install the adjusting lock cap and a new cotter pin.
| 5. INSTALL FRONT AXLE HUB GREASE CAP |
| 6. INSTALL FRONT SPEED SENSOR |
Type A:
Install the skid control sensor wire onto the steering knuckle with the bolt.
- Torque:
- 13 N*m{ 127 kgf*cm , 9 ft.*lbf }
Engage the 3 clamps.
Using a 5 mm hexagon wrench, install the speed sensor with the bolt.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
Type B:
Install the skid control sensor wire onto the steering knuckle with the 2 bolts.
- Torque:
- 13 N*m{ 127 kgf*cm , 9 ft.*lbf }
Engage the clamp.
Install the speed sensor with the bolt.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
| 7. INSTALL FRONT WHEEL |
- Torque:
- 112 N*m{ 1137 kgf*cm , 82 ft.*lbf }
| 8. INSPECT DIFFERENTIAL OIL |
![]() ![]() |
Stop the vehicle on a level surface.
Remove the differential filler plug and gasket.
Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the differential filler plug hole.
- NOTICE:
- After changing the oil seal, drive the vehicle and then check the oil level again.
- After changing the oil seal, drive the vehicle and then check the oil level again.
- Too much or too little oil will lead to differential problems.
- Too much or too little oil will lead to differential problems.
- HINT:
- If necessary, fill the differential carrier assembly with hypoid gear oil.
- Front Differential:
Item
Temperature
Oil grade
Viscosity
Capacity
w/ A.D.D.
-
Hypoid gear oil API GL-4 or GL-5
SAE 75W-90
1.45 to 1.55 liters
(1.53 to 1.63 US qts, 1.27 to 1.36 Imp. qts.)
w/o A.D.D.
Above -18 °C (-0.4 °F)
SAE 90
1.35 to 1.45 liters
(1.42 to 1.53 US qts, 1.18 to 1.27 Imp. qts.)
Below -18 °C (-0.4 °F)
SAE 85W-90
- Rear Differential:
Item
Temperature
Oil grade
Viscosity
Capacity
w/o Differential lock
Above -18 °C (-0.4 °F)
Hypoid gear oil API GL-5
SAE 90
2.95 to 3.05 liters
(3.12 to 3.22 US qts, 2.60 to 2.68 Imp. qts.)
Below -18 °C (-0.4 °F)
SAE 85W-90
w/ Differential lock
Above -18 °C (-0.4 °F)
SAE 90
2.85 to 2.95 liters
(3.01 to 3.12 US qts, 2.51 to 2.60 Imp. qts.)
Below -18 °C (-0.4 °F)
SAE 85W-90
Check for oil leakage when the oil level is low.
Install the differential filler plug with a new gasket.
- Torque:
- Front differential:
- 39 N*m{ 400 kgf*cm , 29 ft.*lbf }
- Rear differential:
- 49 N*m{ 500 kgf*cm , 36 ft.*lbf }
| 9. CHECK VSC SENSOR SIGNAL |
| 10. CHECK FOR DIFFERENTIAL OIL LEAKAGE |
| 11. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |




