2011-2016 FJ Cruiser · Service Manual DRIVE LINE

REASSEMBLY

Removal / installation · Vehicles built from Aug 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


1. INSTALL OUTBOARD JOINT BOOT

C177228E02
  1. Wrap the spline of the outboard joint shaft with protective tape.

    Text in Illustration 
    *1
    Protective Tape

  1. Install new parts onto the outboard joint shaft in the following order.

    1.
    Front axle outboard joint boot No. 2 clamp
    2.
    Front axle outboard joint boot
    3.
    Front axle outboard joint boot clamp

  1. Pack the joint portion of the outboard joint shaft and outboard joint boot with grease.

    Grease capacity:
    266 to 276 g (9.4 to 9.7 oz.)

  1. Install the outboard joint boot onto the outboard joint shaft groove.

    NOTICE:
    Keep the groove free of grease.


2. INSTALL FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP
  1. Fix the outboard joint shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. F052126E04
    Place SST onto the boot clamp, press it against the boot and slightly tighten SST.
    Text in Illustration 
    *a
    Hold
    *b
    Turn
    SST
    09521-24010  

  1. Fix SST and tighten it so that the clearance comes to within the specified range.

    Clearance:
    2.1 mm (0.083 in.) or less

  1. Remove SST.

  1. F052127E01
    Using SST, measure the clearance of the boot clamp as shown in the illustration.
    SST
    09240-00020  

    Clearance:
    2.1 mm (0.083 in.) or less

    NOTICE:
    If the clearance is outside the specified range, retighten it.


3. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

C081563E03
  1. Fix the outboard joint shaft in a vise between aluminum plates.

    Text in Illustration 
    *a
    Hold
    *b
    Turn

    NOTICE:
    Do not overtighten the vise.

  1. Place SST onto the boot clamp, press it against the boot and slightly tighten SST.

    SST
    09521-24010  

  1. Fix SST and tighten it so that the clearance comes to within the specified range.

    Clearance:
    1.3 mm (0.051 in.) or less

  1. Remove SST.

  1. C092627E01
    Using SST, measure the clearance of the boot clamp as shown in the illustration.
    SST
    09240-00020  

    Clearance:
    1.3 mm (0.051 in.) or less

    NOTICE:
    If the clearance is outside the specified range, retighten it.


4. INSTALL FRONT DRIVE SHAFT DUST COVER

  1. F041033E01
    Using SST and a press, install a new dust cover into the inboard joint until it is flush with the end.
    SST
    09527-10011  

    NOTICE:
    1. Install the dust cover in the correct orientation.
    2. Do not deform the dust cover.


5. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING
  1. Install a new snap ring.


6. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY
  1. Install new parts onto the outboard joint shaft in the following order.

    1.
    Front axle inboard joint boot clamp
    2.
    Front axle inboard joint boot
    3.
    Front axle inboard joint boot No. 2 clamp

  1. Fix the outboard joint shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Remove the protective tape.

  1. C067417E30
    Align the matchmarks and install the tripod joint onto the outboard joint shaft.
    Text in Illustration 
    *a
    Beveled
    *b
    Matchmarks

    NOTICE:
    Place the beveled side of the tripod toward the inboard joint.

  1. Using a brass bar and hammer, install the tripod joint.

    NOTICE:
    1. Do not hit the roller portion.
    2. Keep the tripod joint free of foreign matter.

  1. G022501
    Using a snap ring expander, install a new snap ring.

  1. Pack the inboard joint with grease.

    Grease capacity:
    239 to 249 g (8.4 to 8.8 oz.)

  1. C054086E02
    Align the matchmarks and install the inboard joint onto the outboard joint shaft.
    Text in Illustration 
    *a
    Matchmarks


7. INSTALL INBOARD JOINT BOOT
  1. Install the inboard joint boot into the grooves of the inboard joint and outboard joint shaft.

    NOTICE:
    Keep the grooves free of grease.


8. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

D026925E18
  1. Fix the outboard joint shaft in a vise between aluminum plates.

    Text in Illustration 
    *a
    Hold
    *b
    Turn

    NOTICE:
    Do not overtighten the vise.

  1. Place SST onto the boot clamp, press it against the boot and slightly tighten SST.

    SST
    09521-24010  

  1. Fix SST and tighten it so that the clearance comes to within the specified range.

    Clearance:
    1.3 mm (0.051 in.) or less

    NOTICE:
    If the clearance is outside the specified range, retighten it.

  1. Remove SST.

  1. D026926
    Using SST, measure the clearance of the boot clamp as shown in the illustration.
    SST
    09240-00020  

    Clearance:
    1.3 mm (0.051 in.) or less

    NOTICE:
    If the clearance is outside the specified range, retighten it.


9. INSTALL FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP

G022110E02
  1. Check whether the drive shaft dimensions are within the following specifications.

    Text in Illustration 
    *a
    Dimension A

    Dimension (A):
    577.5 mm (22.74 in.)

  1. Fix the outboard joint shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. C108292E14
    Place SST onto the boot clamp, press it against the boot and slightly tighten SST.
    Text in Illustration 
    *a
    Hold
    *b
    Turn
    SST
    09521-24010  

  1. Fix SST and tighten it so that the clearance comes to within the specified range.

    Clearance:
    2.1 mm (0.082 in.) or less

  1. Remove SST.

  1. C086270E09
    Using SST, measure the clearance of the boot clamp as shown in the illustration.
    SST
    09240-00020  

    Clearance:
    2.1 mm (0.082 in.) or less

    NOTICE:
    If the clearance is outside the specified range, retighten it.


10. INSPECT FRONT DRIVE SHAFT

W001721
  1. Check for noticeable looseness when turning the joint up and down, left and right, and in the thrust direction.

  1. Check for cracks, damage and grease leakage on the boot joint.

    NOTICE:
    Keep the drive shaft level while moving it.

← REASSEMBLY (Jul 2007 – Jul 2009)INSTALLATION (Jul 2007 – Oct 2010) →