2011-2016 FJ Cruiser · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Jul 2007


1. INSTALL FRONT DISC
  1. Align the matchmarks of the disc and axle hub and install the disc.

    HINT:
    When replacing the disc, select the position that gives the minimum disc runout.


2. INSTALL DISC BRAKE CYLINDER ASSEMBLY

F050211
  1. Install the disc brake cylinder with the 2 bolts.

    Torque:
    123 N*m{ 1,254 kgf*cm , 91 ft.*lbf }

  1. C168981E01
    Using a union nut wrench, install the brake tube onto the disc brake cylinder.

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 144 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.866 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to a torque wrench.


3. INSTALL FRONT ANTI SQUEAL SHIM KIT

NOTICE:
If necessary, replace the anti squeal shim when replacing the brake pad.

  1. C133116E01
    Apply disc brake grease to both sides of each No. 1 shim.

  1. Install the No. 1 and No. 2 anti squeal shims onto each brake pad.


4. INSTALL FRONT DISC BRAKE PAD
  1. Install the 2 disc brake pads with anti squeal shims onto the disc brake cylinder.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the disc brake pads or the front disc.


5. INSTALL FRONT DISC BRAKE ANTI RATTLE WITH HOLE PIN

F043185E03
  1. Install the anti rattle spring and 2 hole pins onto the disc brake cylinder.

    HINT:
    The anti rattle spring is installed onto the lower hole pin.

  1. Install the 2 new pin hold clips onto the hole pin.

    NOTICE:
    Install the pin hold clip with its handle oriented in the center of the vehicle.


6. BLEED BRAKE LINE
  1. Turn the ignition switch to ON.

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.

  1. Repeatedly depress the brake pedal and bleed air from the bleeder plug of the front disc brake cylinder RH.

  1. Repeat the step above until the air is completely bled, and then tighten the bleeder plug while depressing the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.

  1. With the brake pedal depressed, loosen the bleeder plug of the rear disc brake cylinder RH, continue to hold the brake pedal and allow brake fluid to be drained from the bleeder plug while the pump motor operates.

    HINT:
    1. Air is bled as the pump motor operates while the brake pedal is being depressed.
    2. Be sure to release the brake pedal to stop the motor after approximately 100 seconds of continuous operation.
    3. As brake fluid is continuously drained while the pump operates, it is not necessary to repeatedly depress the brake pedal.

  1. When there is no more air in the brake fluid, tighten the bleeder plug, and then release the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.

  1. Turn the ignition switch off.

  1. Inspect for brake fluid leaks.

  1. Check and adjust the brake fluid level (Click here).

  1. Clear the DTCs (Click here).


7. INSTALL FRONT WHEEL

Torque:
112 N*m{ 1,137 kgf*cm , 82 ft.*lbf }

← REASSEMBLY (from Jul 2007)COMPONENTS (from Jul 2007) →