INSTALLATION
Removal / installation · Vehicles built Nov 2010 – Jul 2012
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012
| 1. INSTALL HYDRAULIC BRAKE BOOSTER (for LHD) |
Install a new gasket onto the hydraulic brake booster.
Install the hydraulic brake booster with the 4 nuts.
- Torque:
- 14 N*m{ 145 kgf*cm , 10 ft.*lbf }
Temporarily install each brake tube to the correct positions of the brake actuator as shown in the illustration.

Text in Illustration *a
To front wheel cylinder RH
*b
To front wheel cylinder LH
*c
To rear wheel cylinder RH
*d
To rear wheel cylinder LH
Using a union nut wrench 10 mm, connect the 4 brake tubes onto the hydraulic brake booster.
- Torque:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- NOTICE:
- Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).
Connect the 3 connectors.

| 2. INSTALL HYDRAULIC BRAKE BOOSTER (for RHD) |
Install a new gasket onto the hydraulic brake booster.
Install the hydraulic brake booster with the 4 nuts.
- Torque:
- 14 N*m{ 145 kgf*cm , 10 ft.*lbf }
Temporarily install each brake tube to the correct positions of the brake actuator as shown in the illustration.

Text in Illustration *a
To front wheel cylinder RH
*b
To front wheel cylinder LH
*c
To rear wheel cylinder RH
*d
To rear wheel cylinder LH
Install the brake tube clamp to the brake tube.
Install the brake tube clamp with the bolt.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
Using a union nut wrench 10 mm, connect the 4 brake tubes onto the hydraulic brake booster.
- Torque:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- NOTICE:
- Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).
Connect the 3 connectors.

| 3. INSTALL MASTER CYLINDER PUSH ROD CLEVIS |
Apply lithium soap base glycol grease to the inner surface of the hole in the brake pedal lever.
Install the push rod clevis onto the brake pedal lever with the push rod pin and clip.
| 4. BLEED BRAKE SYSTEM |
- CAUTION:
- If air is bled without using the intelligent tester, damage or accidents may result. Therefore, always use the intelligent tester when bleeding air.
Turn the ignition switch to ON.
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.
Repeatedly depress the brake pedal and bleed air from the bleeder plug of the front disc brake cylinder RH.
Repeat the step above until the air is completely bled, and then tighten the bleeder plug while depressing the brake pedal.
- Torque:
- 11 N*m{ 110 kgf*cm , 8 ft.*lbf }
Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.
With the brake pedal depressed, loosen the bleeder plug of the rear disc brake cylinder RH, continue to hold the brake pedal and allow brake fluid to be drained from the bleeder plug while the pump motor operates.
- HINT:
- Air is bled as the pump motor operates while the brake pedal is being depressed.
- Be sure to release the brake pedal to stop the motor after approximately 100 seconds of continuous operation.
- As brake fluid is continuously drained while the pump operates, it is not necessary to repeatedly depress the brake pedal.
- Air is bled as the pump motor operates while the brake pedal is being depressed.
When there is no more air in the brake fluid, tighten the bleeder plug, and then release the brake pedal.
- Torque:
- 11 N*m{ 110 kgf*cm , 8 ft.*lbf }
Bleed the air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.
Turn the ignition switch off and connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Air Bleeding.
- NOTICE:
- To protect the solenoid from overheating, the solenoid operation stops automatically in 4 seconds, and then the solenoid will not respond to commands for an additional 20 seconds.
Repeatedly depress the brake pedal several times, and then, with the brake pedal depressed, turn FR on and bleed air.
- HINT:
- Air returns to the brake master cylinder reservoir together with the brake fluid and is bled from the brake system.
- NOTICE:
- As it is not possible to visually confirm that air is being bled, repeat this step 10 times.
- Do not loosen the bleeder plug.
- As it is not possible to visually confirm that air is being bled, repeat this step 10 times.
Turn FL on and bleed air using the same procedures as for FR.
Turn RR on, loosen the bleeder plug of the rear disc brake cylinder RH and drain brake fluid.
- HINT:
- Do not depress the brake pedal.
- As brake fluid is automatically drained while the pump and solenoid operate, it is not necessary to operate the brake pedal.
- Do not depress the brake pedal.
Repeat the step above until the air is completely bled, and then tighten the bleeder plug.
- Torque:
- 11 N*m{ 110 kgf*cm , 8 ft.*lbf }
Turn FL Line on and bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.
Turn RR Line on and loosen the bleeder plug of the rear disc brake cylinder RH.
- HINT:
- Be sure to bleed air with the brake pedal depressed.
Repeat the step above until the air is completely bled, and then tighten the bleeder plug.
- Torque:
- 11 N*m{ 110 kgf*cm , 8 ft.*lbf }
Turn RL Line on and bleed air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.
Turn the intelligent tester off and turn the ignition switch off.
Inspect for brake fluid leaks.
Check and adjust the brake fluid level (Click here).
Clear the DTCs (Click here).
| 5. INSPECT AND ADJUST BRAKE PEDAL |
![]() ![]() |
Inspect the brake pedal height.
Text in Illustration *a
Pedal height
If the pedal height is incorrect, adjust the rod operating adapter length.Pedal height from dash panel: for LHD
for RHD
168.7 to 178.7 mm (6.642 to 7.035 in.)
158.8 to 168.8 mm (6.252 to 6.645 in.)
Adjust the brake pedal height.
Disconnect the connector from the stop light switch.
Turn the stop light switch counterclockwise, and remove the stop light switch.
Remove the hydraulic brake booster (Click here).
Loosen the clevis lock nut.

Adjust the rod operating adapter length by turning the pedal push rod clevis.
- Rod operating adapter length A:
- 201.7 to 202.7 mm (7.941 to 7.980 in.)
Tighten the clevis lock nut.
- Torque:
- 26 N*m{ 260 kgf*cm , 19 ft.*lbf }
Install the hydraulic brake booster (Click here).
Insert the stop light switch into the adjuster until it just touches the brake pedal.

Text in Illustration *1
Brake pedal
*2
Stop light switch mounting adjuster
*3
Stop light switch
- NOTICE:
- Do not depress the brake pedal.
Make a quarter turn clockwise to install the stop light switch.

Text in Illustration *1
Shaft
*2
Stop light switch
*a
Stop light switch clearance
- NOTICE:
- Do not depress the brake pedal.
- HINT:
- The turning torque for installing the stop light switch:
- Torque:
- 1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less
Check the stop light switch clearance.
- Stop light switch clearance:
- 0.5 to 2.6 mm (0.020 to 0.102 in.)
Connect the connector to the stop light switch.
Inspect the brake pedal free play.

Text in Illustration *a
Pedal free play
Stop the engine and depress the brake pedal several times until there is no vacuum left in the booster.
Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.
- Pedal free play:
- 1.0 to 6.0 mm (0.0394 to 0.236 in.)
Inspect the brake pedal reserve distance.

Text in Illustration *a
Pedal reserve distance
Release the parking brake pedal.
With the engine running, depress the pedal and measure the pedal reserve distance as shown.
If incorrect, troubleshoot the brake system.Pedal reserve distance from dash panel at 490 N (50 kgf, 110.2 lbf) for LHD
for RHD
More than 56 mm (2.20 in.)
More than 108 mm (4.25 in.)
| 6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL |
Engage the 5 clips and claw and install the lower instrument panel finish panel.
Install the 2 <E> bolts.
| 7. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL |
Connect the connectors.
Engage the 8 clips and 4 guides and install the lower instrument panel finish panel.
Install the 2 <E> bolts.
| 8. INSTALL INSTRUMENT PANEL FINISH PLATE |
Install the instrument panel finish plate.

Text in Illustration *1
Instrument Panel Finish Plate
| 9. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
Engage the 3 claws and install the hood lock control lever.
| 10. CONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for RHD) |
Engage the 3 claws and install the fuel lid lock open lever.
| 11. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY |
Engage the 4 clips and 2 claws and install the instrument panel register.
| 12. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP |
Install the front door opening trim weatherstrip.
| 13. INSTALL COWL SIDE TRIM BOARD |
- HINT:
- Use the same procedure as for the RH side.
| 14. INSTALL FOOTREST CLIP |
![]() ![]() |
- HINT:
- Use the same procedure for both sides.
Engage the 2 claws and install the footrest clip.
| 15. INSTALL FRONT FLOOR FOOTREST |
Engage the 2 studs and install the front floor footrest.

| 16. INSTALL FRONT DOOR SCUFF PLATE |
- HINT:
- Use the same procedure as for the RH side.
| 17. INSPECT BRAKE MASTER CYLINDER OPERATION |
Inspect the positive battery voltage.
- Standard voltage:
- 11 to 14 V
Turn the ignition switch to OFF, and depress the brake pedal more than 20 times.
- HINT:
- When pressure in the accumulator is released, the reaction force becomes lighter and the stroke becomes longer.
Check that the brake pedal becomes easy to depress.
If the pedal does not become easy to depress, check and replace the brake line and hydraulic brake booster.
Turn the ignition switch to ON and check the pump motor operation noise.
If the pump motor does not operate, check and replace the wire harness and pump motor (Click here).
Connect the intelligent tester.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Select "ACTIVE TEST" mode on the intelligent tester.
- HINT:
- Refer to the intelligent tester operator manual for further details.
- To protect the solenoids, intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- Refer to the intelligent tester operator manual for further details.
Check the master cylinder solenoid operation.


Inspection Order
(Step)
SOL Selected By Active Test
SOL To Be Activated
D
SRCF (SA1)
SMCF
E
SRCF & SRCR
SREA
F
SFRH
SFRH
G
SFLH
SFLH
H
SFRR & SFRH
SFRR
I
SFLR & SFLH
SFLR
J
SRMF (SMCF, SA3)
SREC
K
SRMR (SMCR, STR)
STR
L
SRRH
SRRH
M
SRLH
SRLH
N
SRH & SRR
SRRR
O
SRLR & SRLH
SRLR
Prepare the vehicle.
Jack up and support the vehicle.
Release the parking brake lever.
Shift the shift lever to the "N" position and check that the rear wheels rotate by hand.
Inspect front VSC solenoid (SMCF) operation (step D).
- HINT:
- ON: Activate SMCF and check that the brake pedal cannot be depressed (the pedal feels tight).
- OFF: Deactivate SMCF and check that the brake pedal can be depressed.
- ON: Activate SMCF and check that the brake pedal cannot be depressed (the pedal feels tight).
Select "SRCF (SA1)" on the intelligent tester.
Turn the "SRCF (SA1)" on by the intelligent tester, then depress the brake pedal with stable force and check that the pedal cannot be depressed.
If the pedal can be depressed, replace the hydraulic brake booster.- HINT:
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- NOTICE:
- When operating it continuously, set the interval of more than 20 seconds.
Release the brake pedal.
When the solenoid is off, depress the brake pedal again and check that the brake pedal can be depressed.
If the pedal cannot be depressed, replace the hydraulic brake booster.
Inspect front VSC solenoid (SREA) operation (step E).
- HINT:
- ON: Activate SMCF and SREA, depress the brake pedal, and then check that the front wheels do not rotate.
- OFF: Deactivate SMCF and SREA. Reactivate SMCF, depress the brake pedal, and then check that the front wheels rotate.
- ON: Activate SMCF and SREA, depress the brake pedal, and then check that the front wheels do not rotate.
Select "SRCF & SRCR" on the intelligent tester.
Turn the "SRCF & SRCR" on by the intelligent tester, then depress the brake pedal with stable force.
When the solenoids are on, check that the front wheels do not rotate by hand.
If the front wheels rotate, replace the hydraulic brake booster.- HINT:
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- When rotating the wheels fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheels as slowly as possible.
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- NOTICE:
- When operating it continuously, set the interval of more than 20 seconds.
When the solenoids are off, turn the "SRCF (SA1)" on by the intelligent, then depress the brake pedal and check the front wheels by rotating them by hand.
If the front wheels stop, replace the hydraulic brake booster.When the "SRCF (SA1)" is off, depress the brake pedal again and check that the brake pedal can be depressed.
If the pedal cannot be depressed, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFRH) operation (step F).
- HINT:
- ON: Activate SFRH, depress the brake pedal, and then check that the right front wheel rotates.
- OFF: Deactivate SFRH, depress the brake pedal, and then check that the right front wheel does not rotate.
- ON: Activate SFRH, depress the brake pedal, and then check that the right front wheel rotates.
Select "SFRH" on the intelligent tester.
Turn the "SFRH" on by the intelligent tester, then depress the brake pedal with stable force.
When the solenoid is on, check the right front wheel by rotating it by hand.
If the right front wheel stops, replace the hydraulic brake booster.- HINT:
- To protect the solenoid, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.
- To protect the solenoid, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- NOTICE:
- When operating it continuously, set the interval of more than 20 seconds.
When the solenoid is off, depress the brake pedal again and check that the right front wheel does not rotate by hand.
If the right front wheel rotates, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFLH) operation (step G).
- HINT:
- ON: Activate SFLH, depress the brake pedal, and then check that the left front wheel rotates.
- OFF: Deactivate SFLH, depress the brake pedal, and then check that the left front wheel does not rotate.
- ON: Activate SFLH, depress the brake pedal, and then check that the left front wheel rotates.
Select "SFLH" on the intelligent tester.
Turn the "SFLH" on by the intelligent tester, then depress the brake pedal with stable force.
When the solenoid is on, check the left front wheel by rotating it by hand.
If the left front wheel stops, replace the hydraulic brake booster.- HINT:
- To protect the solenoid, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.
- To protect the solenoid, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- NOTICE:
- When operating it continuously, set the interval of more than 20 seconds.
When the solenoid is off, depress the brake pedal again and check that the left front wheel does not rotate by hand.
If the left front wheel rotates, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFRR) operation (step H).
- HINT:
- ON: Depress the brake pedal, activate SFRR and SFRH, and then check that the right front wheel rotates.
- OFF: Deactivate SFRR and SFRH, depress the brake pedal, and then check that the right front wheel does not rotate.
- ON: Depress the brake pedal, activate SFRR and SFRH, and then check that the right front wheel rotates.
Select "SFRR & SFRH" on the intelligent tester.
Depress the brake pedal with stable force, then turn the "SFRR & SFRH" on by the intelligent tester.
When the solenoids are on, check the right front wheel by rotating it by hand.
If the right front wheel stops, replace the hydraulic brake booster.- HINT:
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- NOTICE:
- When operating it continuously, set the interval of more than 20 seconds.
When the solenoids are off, depress the brake pedal again and check that the right front wheel does not rotate by hand.
If the right front wheel rotates, replace the hydraulic brake booster.
Inspect front ABS solenoid (SFLR) operation (step I).
- HINT:
- ON: Depress the brake pedal, activate SFLR and SFLH, and then check that the left front wheel rotates.
- OFF: Deactivate SFLR and SFLH, depress the brake pedal, and then check that the left front wheel does not rotate.
- ON: Depress the brake pedal, activate SFLR and SFLH, and then check that the left front wheel rotates.
Select "SFLR & SFLH" on the intelligent tester.
Depress the brake pedal with stable force, then turn the "SFLR & SFLH" on by the intelligent tester.
When the solenoids are on, check the left front wheel by rotating it by hand.
If the left front wheel stops, replace the hydraulic brake booster.- HINT:
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- NOTICE:
- When operating it continuously, set the interval of more than 20 seconds.
When the solenoids are off, depress the brake pedal again and check that the left front wheel does not rotate by hand.
If the left front wheel rotates, replace the hydraulic brake booster.
Inspect rear VSC solenoid (SREC) operation (step J).
- HINT:
- ON: Depress the brake pedal, and activate SREC. Release the brake pedal and check that the rear wheels do not rotate.
- OFF: Deactivate SREC and check that the rear wheels rotate.
- ON: Depress the brake pedal, and activate SREC. Release the brake pedal and check that the rear wheels do not rotate.
Select "SRMF (SMCF, SA3)" on the intelligent tester.
Depress the brake pedal with stable force, then turn the "SRMF (SMCF, SA3)" on by the intelligent tester.
Release the brake pedal when the solenoid is on, and check that the rear wheels do not rotate by hand.
If the rear wheels rotate, replace the hydraulic brake booster.- HINT:
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- When rotating the wheels fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheels as slowly as possible.
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- NOTICE:
- When operating it continuously, set the interval of more than 20 seconds.
When the solenoid is off, check the rear wheels by rotating them by hand.
If the rear wheels stop, replace the hydraulic brake booster.
Inspect rear VSC solenoid (STR) operation (step K).
- HINT:
- ON: Activate STR, depress the brake pedal, and then check that the rear wheels rotate.
- OFF: Deactivate STR, depress the brake pedal, and then check that the rear wheels do not rotate.
- ON: Activate STR, depress the brake pedal, and then check that the rear wheels rotate.
Select "SRMR (SMCR, STR)" on the intelligent tester.
Turn the "SRMR (SMCR, STR) on by the intelligent tester.
When the solenoid is on, check that the rear wheels rotate by hand.
If the rear wheels do not rotate, replace the hydraulic brake booster.- HINT:
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- When rotating the wheels fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheels as slowly as possible.
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- NOTICE:
- When operating it continuously, set the interval of more than 20 seconds.
When the "SRMR (SMCR, STR)" is off, depress the brake pedal again and check that the rear wheels do not rotate by hand.
If the rear wheels rotate, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRRH) operation (step L).
- HINT:
- ON: Activate SRRH, depress the brake pedal, and then check that the right rear wheel rotates.
- OFF: Deactivate SRRH, depress the brake pedal, and then check that the right rear wheel does not rotate.
- ON: Activate SRRH, depress the brake pedal, and then check that the right rear wheel rotates.
Select "SRRH" on the intelligent tester.
Turn the "SRRH" on by the intelligent tester, then depress the brake pedal with stable force.
When the solenoid is on, check the right rear wheel by rotating it by hand.
If the right rear wheel stops, replace the hydraulic brake booster.- HINT:
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- NOTICE:
- When operating it continuously, set the interval of more than 20 seconds.
When the solenoid is off, depress the brake pedal again and check that the right rear wheel does not rotate by hand.
If the right rear wheel rotates, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRLH) operation (step M).
- HINT:
- ON: Activate SRLH, depress the brake pedal, and then check that the left rear wheel rotates.
- OFF: Deactivate SRLH, depress the brake pedal, and then check that the left rear wheel does not rotate.
- ON: Activate SRLH, depress the brake pedal, and then check that the left rear wheel rotates.
Select "SRLH" on the intelligent tester.
Turn the "SRLH" on by the intelligent tester, then depress the brake pedal with stable force.
When the solenoid is on, check the left rear wheel by rotating it by hand.
If the left rear wheel stops, replace the hydraulic brake booster.- HINT:
- To protect the solenoid, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.
- To protect the solenoid, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- NOTICE:
- When operating it continuously, set the interval of more than 20 seconds.
When the solenoid is off, depress the brake pedal again and check that the left rear wheel does not rotate by hand.
If the left rear wheel rotates, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRRR) operation (step N).
- HINT:
- ON: Depress the brake pedal, activate SRRH and SRRR, and then check that the right rear wheel rotates.
- OFF: Deactivate SRRH and SRRR, depress the brake pedal, and then check that the right rear wheel does not rotate.
- ON: Depress the brake pedal, activate SRRH and SRRR, and then check that the right rear wheel rotates.
Select "SRH & SRR" on the intelligent tester.
Depress the brake pedal with stable force, then turn the "SRH & SRR" on by the intelligent tester.
When the solenoids are on, check the right rear wheel by rotating it by hand.
If the right rear wheel stops, replace the hydraulic brake booster.- HINT:
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- NOTICE:
- When operating it continuously, set the interval of more than 20 seconds.
When the solenoids are off, depress the brake pedal again and check that the right rear wheel does not rotate by hand.
If the right rear wheel rotates, replace the hydraulic brake booster.
Inspect rear ABS solenoid (SRLR) operation (step O).
- HINT:
- ON: Depress the brake pedal, activate SRLR and SRLH, and then check that the left rear wheel rotates.
- OFF: Deactivate SRLR and SRLH, depress the brake pedal, and then check that the left rear wheel does not rotate.
- ON: Depress the brake pedal, activate SRLR and SRLH, and then check that the left rear wheel rotates.
Select "SRLR & SRLH" on the intelligent tester.
Depress the brake pedal with stable force, then turn the "SRLR & SRLH" on by the intelligent tester.
When the solenoids are on, check the left rear wheel by rotating it by hand.
If the left rear wheel stops, replace the hydraulic brake booster.- HINT:
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly as possible.
- To protect the solenoids, the intelligent tester turns off automatically 2 seconds after every solenoid has been turned on.
- NOTICE:
- When operating it continuously, set the interval of more than 20 seconds.
When the solenoids are off, depress the brake pedal again and check that the left rear wheel does not rotate by hand.
If the left rear wheel rotates, replace the hydraulic brake booster.
Lower the vehicle.
Disconnect the intelligent tester.


