INSTALLATION
Removal / installation · Vehicles built Aug 2009 – Oct 2010
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
| 1. INSTALL OIL COOLER ASSEMBLY |
Install a new seal washer to the bolt.
Install the oil cooler with the bolt and nut.
- Torque:
- for bolt:
- 68 N*m{ 693 kgf*cm , 50 ft.*lbf }
- for nut:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
Install the 2 hoses.

Text in Illustration *a
Upper
*b
Rear
- HINT:
- The direction of the hose clamp is indicated in the illustration.
| 2. INSTALL OIL FILTER BRACKET |
Install the oil filter bracket and new gasket with the 2 nuts and bolt.
- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
| 3. CONNECT WATER BY-PASS PIPE SUB-ASSEMBLY |
![]() ![]() |
Connect the 2 hoses and water by-pass pipe.
Text in Illustration *a
Upper
*b
Rear
- HINT:
- The direction of the hose clamp is indicated in the illustration.
Install the 3 bolts.
- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
| 4. INSTALL OIL FILTER ELEMENT |
Clean the inside of the oil filter cap, the threads and O-ring groove.
Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.
Set a new oil filter element to the oil filter cap.
Remove any dirt or foreign matter from the installation surface of the engine.
Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.
Using SST, tighten the oil filter cap.

Text in Illustration *1
Oil Filter Bracket Clip
*a
No Clearance
- SST
- 09228-06501
- Torque:
- 25 N*m{ 255 kgf*cm , 18 ft.*lbf }
- NOTICE:
- When tightening the oil filter cap, do not remove the oil filter bracket clip.
- Make sure that the oil filter is installed securely as shown in the illustration.
- Be careful that the O-ring does not get caught between the parts.
- When tightening the oil filter cap, do not remove the oil filter bracket clip.
Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

Text in Illustration *1
O-Ring
- NOTICE:
- Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.
Install the oil filter drain plug.
- Torque:
- 13 N*m{ 127 kgf*cm , 9 ft.*lbf }
- NOTICE:
- Be careful that the O-ring does not get caught between the parts.
| 5. ADD ENGINE OIL |
Add fresh oil.
- Standard Engine Oil:
Oil grade
Oil Viscosity (SAE)
API grade SL "Energy- Conserving", SM "Energy- Conserving" or ILSAC multigrade engine oil
0W-20
5W-20
5W-30
10W-30
API grade SL or SM multigrade engine oil
15W-40
20W-50
- Standard Oil Capacity (w/o Oil Cooler):
Item
Specified Condition
Drain and refill without oil filter change
5.7 liters (6.0 US qts, 5.0 Imp. qts)
Drain and refill with oil filter change
6.1 liters (6.4 US qts, 5.4 Imp. qts)
Dry fill
6.9 liters (7.3 US qts, 6.1 Imp. qts)
- Standard Oil Capacity (w/ Oil Cooler):
Item
Specified Condition
Drain and refill without oil filter change
5.7 liters (6.0 US qts, 5.0 Imp. qts)
Drain and refill with oil filter change
6.2 liters (6.6 US qts, 5.5 Imp. qts)
Dry fill
7.1 liters (7.5 US qts, 6.3 Imp. qts)
| 6. CHECK ENGINE OIL LEVEL |
Warm up the engine, then stop the engine and wait for 5 minutes.
Check that the engine oil level is between the low level and full level marks on the dipstick.
If low, check for leakage and add oil up to the full level mark.- NOTICE:
- Do not fill engine oil above the full level mark.
| 7. ADD ENGINE COOLANT |
Tighten the 2 cylinder block drain cock plugs.
- Torque:
- 13 N*m{ 130 kgf*cm , 9 ft.*lbf }
Tighten the radiator drain cock plug by hand.
Add engine coolant.
- Standard Capacity:
Item
Specified Condition
for Automatic Transmission
9.8 liters (10.4 US qts, 8.6 Imp. qts)
for Manual Transmission
9.4 liters (9.9 US qts, 8.3 Imp. qts)
- NOTICE:
- Do not substitute plain water for engine coolant.
- HINT:
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
Slowly pour coolant into the radiator reservoir until it reaches the Full line.

Text in Illustration *1
FULL Line
Install the reservoir cap.
Install the radiator cap.*1
Start the engine and stop it immediately.*2
Allow approximately 10 seconds to pass, and then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3
Repeat steps *1, *2 and *3 until the coolant level does not decrease.
- HINT:
- Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator if the engine is warmed up and the thermostat opens.
Install the radiator cap.*4
Set the air conditioning as follows.*5
Item
Condition
Fan speed
Any setting except off
Temperature
Toward WARM
Air conditioning switch
Off
Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6
- CAUTION:
- Wear protective gloves. Hot areas on the parts may injure your hands.
- Be careful of the fan.
- Be careful as the engine, radiator and radiator hoses are hot and can cause burns.
- Wear protective gloves. Hot areas on the parts may injure your hands.
- NOTICE:
- Immediately after starting the engine, if the radiator reservoir becomes empty, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the Full line.
- Do not start the engine when there is no coolant in the radiator reservoir.
- Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
- If there is not enough coolant, the engine may burn out or overheat.
- Immediately after starting the engine, if the radiator reservoir becomes empty, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the Full line.
- HINT:
- Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air while warming up the engine.
- The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.
- Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air while warming up the engine.
Stop the engine, wait until the engine coolant cools down to ambient temperature, and then remove the radiator cap and check the coolant level.*7
- CAUTION:
- Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8
If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the Full line.

If the coolant level is below the Full line, repeat steps *4 through *8.
If the coolant level is above the Full line, drain coolant until the coolant level reaches the Full line.Text in Illustration *1
FULL Line
| 8. INSPECT FOR ENGINE OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the area that was worked on.
| 9. INSPECT FOR COOLANT LEAK |
- CAUTION:
- To avoid being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion may cause hot engine coolant and steam to blow out from the radiator.
Fill the radiator with engine coolant, and then attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and then check that the pressure does not drop.

If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.Text in Illustration *1
Radiator Cap Tester
| 10. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
Hook the engine under cover to the vehicle body.
Install the 4 bolts.
- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }

