2011-2016 FJ Cruiser · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

A120414
  1. Install a new gasket and the oil filter bracket with the 2 nuts and 3 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


2. INSTALL OIL COOLER ASSEMBLY
  1. Clean the contact surfaces of the oil filter bracket and oil cooler.

  1. Place a new O-ring on the oil cooler.

  1. Apply a light coat of engine oil to the threads of the union bolt.

  1. A076453E01
    Install the oil cooler and plate washer with the union bolt.

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }

  1. Connect the 2 hoses to the oil cooler.


3. INSTALL OIL FILTER SUB-ASSEMBLY

A076324E01
  1. Clean the surface of the oil filter bracket which comes into contact with the oil filter.

  1. Apply clean engine oil to the rubber gasket of a new oil filter.

  1. Tighten the oil filter by hand until the rubber gasket comes into contact with the seat of the filter bracket.

  1. A076325E03
    Using SST, tighten it an additional 3/4 turn to set the filter.
    SST
    09228-07501  

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


4. ADD ENGINE OIL
  1. Add fresh engine oil and install the oil filler cap.

    Engine Oil:
    Oil Grade
    Oil Viscosity (SAE)
    ILSAC multigrade engine oil
    1. 5 W-30
    2. 10 W-30
    (5 W-30 is best choice for fuel economy and good starting in cold wheather.)

    Oil Capacity:
    Item
    Specification
    With oil filter change
    5.2 liters (5.5 US qts, 4.6 lmp. qts)
    Without oil filter change
    4.9 liters (5.2 US qts, 4.3 lmp. qts)
    Dry fill
    6.0 liters (6.3 US qts, 5.3 lmp. qts)

  1. Reinstall the oil filler cap.


5. ADD ENGINE COOLANT
  1. Pour coolant into the radiator until it overflows.

    Capacity:
    Transmission
    Capacity
    Manual Transmission
    9.4 liters (9.9 Us qts, 8.3 Imp. qts)
    Automatic Transmission
    9.8 liters (10.4 Us qts, 8.6 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. New TOYOTA vehicles are filled with TOYOTA SLLC (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)). When replacing the coolant, TOYOTA SLLC is recommended.

  1. Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.

  1. Install the radiator cap securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Condition
      Fan Speed
      Any setting except OFF
      Temperature
      Toward WARM
      Air Conditioning Switch
      OFF

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
      3. If there is not enough coolant, the engine may burn out or overheat.

  1. Squeeze the inlet and outlet radiator hoses several times by hand while warming up the engine to bleed the air.

    CAUTION:
    When pressing the radiator hoses:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, repeat the operation until the coolant level remains at the full level.

  1. Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.


6. INSPECT FOR ENGINE COOLANT LEAK
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Pump it to 177 kPa (1.8 kgf/cm2 25.7 psi), then check for leakage.


7. INSTALL V-BANK COVER

  1. A126475
    Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

← INSPECTION (from Aug 2009)INSTALLATION (Aug 2009 – Oct 2010) →