2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.

  1. A224743
    Unhook the engine under cover from the vehicle body as shown in the illustration.


2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the service hole cover from the engine under cover.

  1. A070279E02
    Install a vinyl hose onto the drain on the radiator side.
    Text in Illustration 
    *1
    Vinyl Hose
    *2
    Tape

  1. Fix the vinyl hose with tape.

    A220213E01

    Text in Illustration 
    *1
    Radiator Cap
    *2
    Reservoir Cap
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the 2 cylinder block drain cock plugs and drain the coolant from the engine.

    NOTICE:
    If coolant is not drained from the radiator drain cock plug, cylinder block drain cock plugs and radiator reservoir, clogging in the radiator or coolant leakage from the seal of water pump may result.


3. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


4. REMOVE OIL FILTER ELEMENT

A094910E09
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    Text in Illustration 
    *1
    Pipe
    *2
    Hose

  1. A222100
    Remove the oil filter drain plug.

  1. A222101E01
    Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.

  1. A222102
    Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring, as shown in the illustration.

  1. A222103E01
    Using SST, remove the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Bracket Clip
    SST
    09228-06501  

    NOTICE:
    Do not remove the oil filter bracket clip.

  1. A153538E03
    Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring on the cap.


5. DISCONNECT WATER BY-PASS PIPE SUB-ASSEMBLY

A225377
  1. Remove the 3 bolts.

  1. A222108
    Disconnect the 2 hoses and water by-pass pipe.


6. REMOVE OIL FILTER BRACKET

A223672E01
  1. Remove the 2 nuts, bolt, oil filter bracket and gasket.

    Text in Illustration 
    *A
    w/ Oil Cooler:
    *B
    w/o Oil Cooler:


7. REMOVE OIL COOLER ASSEMBLY

A222109
  1. Remove the 2 hoses.

  1. A222110
    Remove the bolt, nut and oil cooler.

  1. Remove the seal washer from the bolt.

← REMOVAL (Jul 2007 – Jul 2009)REMOVAL (Nov 2010 – Jul 2011) →