2011-2016 FJ Cruiser · Service Manual STEERING

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Aug 2011

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Jul 2011 from Aug 2011


INSPECT DRIVE BELT

F040449
  1. Visually check the belt for defects, such as excessive wear and frayed cords.
    If any defects are found, replace the drive belt.

    HINT:
    Replace the belt if there are any missing ribs.


BLEED POWER STEERING SYSTEM
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

    1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel to the left or right full lock position and keep it there for 2 to 3 seconds. Then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds (step A).

    2. Repeat step A several times.

  1. Stop the engine.

  1. C133819E02
    Check for foaming or emulsification.
    Text in Illustration 
    *a
    Normal
    *b
    Abnormal
    Especially, if the system has to be bled twice because of foaming or emulsification, check for fluid leakage in the system.

  1. Check the fluid level.


INSPECT FLUID LEVEL

C133820
  1. Keep the vehicle level.

  1. With the engine stopped, check the fluid level in the oil reservoir.
    If necessary, add fluid.

    Fluid:
    ATF "DEXRON" II or III

    HINT:
    Check that the fluid level is within the HOT level range in the reservoir tank. If the fluid is cold, check that it is within the COLD level range.

  1. Start the engine and let it idle.

  1. Turn the steering wheel from lock to lock several times to raise fluid temperature.

    Fluid temperature:
    75 to 80°C (167 to 176°F)

  1. C133819E02
    Check for foaming or emulsification.
    Text in Illustration 
    *a
    Normal
    *b
    Abnormal
    If any foaming or emulsification is identified, bleed the power steering system.

  1. C133821E02
    With the engine idling, measure the fluid level in the oil reservoir.
    Text in Illustration 
    *a
    Engine Idling
    *b
    Engine Stopped
    *c
    5 mm (0.20 in.) or less

  1. Stop the engine.

  1. Wait a few minutes and measure the fluid level in the oil reservoir again.

    Maximum fluid level rise:
    5 mm (0.20 in.)

    If any problems are found, bleed the power steering system again.

  1. Check the fluid level.


INSPECT STEERING FLUID PRESSURE
  1. Disconnect the pressure feed tube from the vane pump (Click here).

  1. Connect SST as shown in the illustration.

    SST
    09640-10010   (09641-01010, 09641-01030, 09641-01060)

    NOTICE:
    Check that the valve of SST is in the open position.

  1. Bleed the power steering system.

  1. Start the engine and let it idle.

  1. Turn the steering wheel from lock to lock several times to raise the fluid temperature.

    Fluid temperature:
    75 to 80 °C (167 to 176 °F)


    C231825E01
    Text in Illustration 
    *1
    Pressure Feed Tube
    *2
    Attachment
    V100135
    IN
    V100136
    OUT

  1. Z015498E16
    With the engine idling, close the valve of SST and check the reading on SST.
    Text in Illustration 
    *1
    Power Steering Fluid Reservoir
    *2
    Power Steering Vane Pump
    *3
    Power Steering Gear
    *a
    Valve closed

    Fluid pressure (8.3 MPA Type):
    8300 to 9000 kPa (85 to 92 kgf/cm2, 1203 to 1305 psi)

    Fluid pressure (10.0 MPA Type):
    10000 to 10700 kPa (102 to 109 kgf/cm2, 1450 to 1552 psi)

    NOTICE:
    1. Do not keep the valve closed for more than 10 seconds.
    2. Do not let the fluid temperature become too high.

  1. Z015499E13
    With the engine idling, fully open the valve.
    Text in Illustration 
    *1
    Power Steering Fluid Reservoir
    *2
    Power Steering Vane Pump
    *3
    Power Steering Gear
    *a
    Valve Open

  1. Measure the fluid pressure at the engine speeds of 1,000 rpm and 3,000 rpm.

    Fluid pressure difference:
    490 kPa (5 kgf/cm2, 71 psi) or less

    NOTICE:
    Do not turn the steering wheel.

  1. Z015500E13
    With the engine idling and valve fully open, turn the steering wheel to the full lock position.
    Text in Illustration 
    *1
    Power Steering Fluid Reservoir
    *2
    Power Steering Vane Pump
    *3
    Power Steering Gear (Lock Position)
    *a
    Valve Open

    Fluid pressure (8.3 MPA Type):
    8300 to 9000 kPa (85 to 92 kgf/cm2, 1203 to 1305 psi)

    Fluid pressure (10.0 MPA Type):
    8300 to 8800 kPa (85 to 90 kgf/cm2, 1203 to 1276 psi)

    NOTICE:
    1. Do not keep the steering wheel in the full lock position for more than 10 seconds.
    2. Do not let the fluid temperature become too high.

  1. Disconnect SST.

  1. Connect the pressure feed tube to the vane pump (Click here).

  1. Bleed the power steering system.


INSPECT STEERING EFFORT

C135459
  1. Center the steering wheel assembly.

  1. Remove the steering pad (Click here).

  1. Start the engine and let it idle.

  1. Measure the steering effort in both directions.

    Steering effort (Reference):
    6.0 N*m (60 kgf*cm, 53 in.*lbf) or less

    HINT:
    Check the tire type, pressure and contact surfaces before making a diagnosis.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Install the steering pad (Click here).

← ON-VEHICLE INSPECTION (Aug 2009 – Jul 2011)COMPONENTS (Jul 2007 – Jul 2009) →