TERMINALS OF ECU
System information · Vehicles built Jul 2007 – Oct 2010
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014
| CHECK MAIN BODY ECU |




Disconnect the 1A, 1B, 1E, and 1H main body ECU connectors.
Measure the voltages and resistances of the wire harness side connectors.
If the result is not as specified, there may be a malfunction in the wire harness.Standard: Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
1H-2 (GND1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
1B-4 (BECU) - Body ground
W-R - Body ground
Power source circuit (From battery)
Always
11 to 14 V
1E-9 (BDR1) - Body ground
B-Y - Body ground
Power source circuit (From battery)
Always
11 to 14 V
Reconnect the main body ECU connectors.
Measure the voltages of the wire harness side connectors.
If the result is not as specified, there may be a malfunction in the wire harness.Standard voltage: Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
1F-8 (SIG) - Body ground
B-R - Body ground
Ignition switch signal
Ignition switch is OFF
Below 1V
Ignition switch is ON
11 to 14 V
1L-9 (ACT+) - Body ground
L-R - Body ground
Driver side door lock motor LOCK drive output
Door control switch or Door key cylinder OFF
Below 1V
Door control switch or driver side door key cylinder ON (LOCK)
11 to 14 V → Below 1 V
1L-6 (ACT+) - Body ground
L-R - Body ground
Passenger side door lock motor LOCK drive output
Door control switch or Door key cylinder OFF
Below 1V
Door control switch or driver side door key cylinder ON (LOCK)
11 to 14 V → Below 1 V
1L-21 (ACT-) - Body ground
L-B - Body ground
Driver side door lock motor UNLOCK drive output
Door control switch or Door key cylinder OFF
Below 1V
Door control switch or driver side door key cylinder ON (UNLOCK)
11 to 14 V → Below 1 V
1L-18 (ACT-) - Body ground
L-B - Body ground
Passenger side door lock motor UNLOCK drive output
Door control switch or Door key cylinder OFF
Below 1V
Door control switch or driver side door key cylinder ON (UNLOCK)
11 to 14 V → Below 1 V
E6-21 (LSWD) - Body ground
W-R - Body ground
Driver side door unlock detection switch input
Driver side door unlocked
Below 1V
Driver side door locked
11 to 14 V
E6-30 (LSWP) - Body ground
B-W - Body ground
Passenger side door unlock detection switch input
Passenger side door unlocked
Below 1V
Passenger side door locked
11 to 14 V
1F-4 (LSR) - Body ground
B - Body ground
Back door unlock detection switch input
Back door unlocked
Below 1V
Back door locked
11 to 14 V
1K-3 (L2) - Body ground
L - Body ground
Driver side and passenger side door key-linked operated door lock switch input
Driver side or passenger side door key cylinder OFF
11 to 14 V
Driver side or passenger side door key cylinder ON (LOCK)
Below 1 V
E6-22 (UL2) - Body ground
Y-G - Body ground
Passenger side or Driver side door key-linked operated door unlock switch input
Passenger side or Driver side door key cylinder OFF
11 to 14 V
Passenger side or Driver side door key cylinder ON (UNLOCK)
Below 1 V
E7-7 (BCTY) - Body ground
W - Body ground
Back door courtesy switch and back window courtesy switch input
Back door or back window open
Below 1V
Back door and back window closed
11 to 14 V
E7-11 (RLCY) - Body ground
P-B - Body ground
Rear LH door courtesy switch input
Rear LH door open
Below 1V
Rear LH door closed
11 to 14 V
E7-12 (RRCY) - Body ground
P-L - Body ground
Rear RH door courtesy switch input
Rear RH door open
Below 1V
Rear RH door closed
11 to 14 V
E7-23 (DCTY) - Body ground
R-B - Body ground
Driver door courtesy switch input
Driver door open
Below 1V
Driver door closed
11 to 14 V
E7-24 (PCTY) - Body ground
G-Y - Body ground
Front passenger door courtesy switch input
Front passenger door open
Below 1V
Front passenger door closed
11 to 14 V
E8-14 (KSW) - Body ground
G-Y - Body ground
Key unlock warning switch input
Key inserted in ignition key cylinder
Below 1V
Key removed from ignition key cylinder
11 to 14 V
E6-23 (MPX2) - Body ground
BR-R - Body ground
Multiplex communication signal
During communication
Signal waveform
| CHECK BACK DOOR ECU |


Disconnect the S2 back door ECU connector.
Measure the voltages and resistances of the wire harness side connectors.
If the result is not as specified, there may be a malfunction in the wire harness.Standard: Terminal No. (Symbols)
Wiring Color
Terminal Description
Condition
Specified Condition
S2-5 (BECU) - Body ground
W-R - Body ground
Power source circuit (From battery)
Always
11 to 14 V
S2-3 (GND) - Body ground)
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the back door ECU connector.
Measure the voltages of the wire harness side connectors.
If the result is not as specified, there may be a malfunction in the wire harness.Standard voltage: Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
SIG (S2-6) Body ground
B-R - Body ground
Ignition switch signal
Ignition switch OFF
Below 1V
Ignition switch ON
11 to 14 V
S5-5 (L) - Body ground
L - Body ground
Back door key-linked operated door lock switch input
Back door key cylinder OFF
11 to 14 V
Back door key cylinder ON (LOCK)
Below 1 V
S5-4 (UL) - Body ground
R - Body ground
Back door key-linked operated door unlock switch input
Driver side door key cylinder OFF
11 to 14 V
Driver side door key cylinder ON (UNLOCK)
Below 1 V
S2-1 (MPX2) - Body ground
BR-R - Body ground
Multiplex communication signal
During communication
Signal waveform
S5-15 (ACT+) - Body ground
G - Body ground
Back door lock motor LOCK drive output
Door control switch or Door key cylinder OFF
Below 1V
Door control switch or driver side door key cylinder ON (LOCK)
11 to 14 V → Below 1 V
S5-14 (ACT-) - Body ground
W - Body ground
Back door lock motor UNLOCK drive output
Door control switch or Door key cylinder OFF
Below 1V
Door control switch or driver side door key cylinder ON (UNLOCK)
11 to 14 V → Below 1 V