2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1820/55 Short in Front Driver Side - Side Squib Circuit

Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012

Also covers:

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012

DESCRIPTION

The driver side - side squib circuit consists of the center airbag sensor assembly and the driver side - front seat side airbag assembly.
This circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side - side squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1820/55
  1. Center airbag sensor assembly detects line short circuit signal in driver side - side squib circuit 5 times during primary check.
  2. Driver side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Driver side floor wire
  2. Driver side - front seat side airbag assembly (Driver side - side squib)
  3. Center airbag sensor assembly
B1821/55
  1. Center airbag sensor assembly detects open circuit signal in driver side - side squib circuit for 2 seconds.
  2. Driver side - side squib malfunction
  3. Center airbag sensor assembly malfunction
B1822/55
  1. Center airbag sensor assembly detects short circuit to ground signal in driver side - side squib circuit for 0.5 seconds.
  2. Driver side - side squib malfunction
  3. Center airbag sensor assembly malfunction
B1823/55
  1. Center airbag sensor assembly detects short circuit to B+ signal in driver side - side squib circuit for 0.5 seconds.
  2. Driver side - side squib malfunction
  3. Center airbag sensor assembly malfunction

WIRING DIAGRAM

C146249E88
C146249E89

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting Check Mode (signal check) with the intelligent tester (Click here).
  2. After selecting Check Mode (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK CONNECTORS (DRIVER SIDE - SIDE SQUIB - DRIVER SIDE FLOOR WIRE)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check the driver side floor wire connector and terminals (on the driver side - front seat side airbag assembly side) and check that the connector is properly connected to the driver side - front seat side airbag assembly.

    Result 
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE DRIVER SIDE FLOOR WIRE

C
CONNECT CONNECTOR PROPERLY
A


2. CHECK DRIVER SIDE - FRONT SEAT SIDE AIRBAG ASSEMBLY (DRIVER SIDE - SIDE SQUIB)

  1. H100871E05
    Disconnect the connector from the driver side - front seat side airbag assembly.

  1. Connect the black wire side of SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect a tester to the driver side - front seat side airbag assembly (driver side - side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert the SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1820/55, B1821/55, B1822/55 and B1823/55 are not output.

    HINT:
    DTCs other than DTC B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Driver Side - Side Squib
    *b
    Center Airbag Sensor Assembly
    *c
    Front view of wire harness connector
    (to Driver Side - Front Seat Side Airbag Assembly)
    *d
    Connector C
    *e
    DLC3
    *f
    DTC 55



NG
Go to step 3
OK

REPLACE DRIVER SIDE - FRONT SEAT SIDE AIRBAG ASSEMBLY (Click here)

3. CHECK CONNECTOR (DRIVER SIDE FLOOR WIRE - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the SST from connector C.

  1. Check the driver side floor wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.

    Result 
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE DRIVER SIDE FLOOR WIRE

C
CONNECT CONNECTOR PROPERLY
A


4. CHECK DRIVER SIDE FLOOR WIRE (DRIVER SIDE - SIDE SQUIB CIRCUIT)

  1. C176196E03
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the center airbag sensor assembly.

  1. Check for short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      La1-1 - Body ground
      Ignition switch ON
      Below 1 V
      La1-2 - Body ground
      Ignition switch ON
      Below 1 V
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      KZ1-1 - Body ground
      Ignition switch ON
      Below 1 V
      KZ1-2 - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      La1-1 - La1-2
      Always
      Below 1 Ω
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      KZ1-1 - KZ1-2
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      La1-1 - Body ground
      Always
      1 MΩ or higher
      La1-2 - Body ground
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      KZ1-1 - Body ground
      Always
      1 MΩ or higher
      KZ1-2 - Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      La1-1 - La1-2
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      KZ1-1 - KZ1-2
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Front Passenger Side - Side Squib
      *b
      Center Airbag Sensor Assembly
      *c
      Driver Side Floor Wire
      *d
      Front view of wire harness connector
      (to Driver Side - Front Seat Side Airbag Assembly)
      *e
      Connector C



NG
REPLACE DRIVER SIDE FLOOR WIRE
OK


5. CHECK CENTER AIRBAG SENSOR ASSEMBLY
  1. Connect the connectors to the driver side - front seat side airbag assembly and the center airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1820/55, B1821/55, B1822/55 and B1823/55 are not output.

    HINT:
    DTCs other than DTC B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1820/55 Short in Front Driver Side - Side Squib Circuit (+ B1821/55, B1822/55, B1823/55) (Jul 2007 – Oct 2010)B1825/56 Short in Side Squib LH Circuit (+ B1826/56, B1827/56, B1828/56) (from Aug 2012) →