2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

CAN Bus Line

Circuit diagnosis · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010

DESCRIPTION

When any DTC for the CAN communication system is output, first measure the resistance between the terminals of the DLC3 to specify the trouble area, and check that there is no short in the CAN main wire, between the CAN bus lines, to +B, or to GND.

WIRING DIAGRAM

C134964E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

    HINT:
    Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK CAN BUS WIRE (MAIN WIRE FOR DISCONNECTION, BUS LINES FOR SHORT CIRCUIT)

  1. C118856E43
    Turn the ignition switch OFF.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E1-6 (CANH) - E1-14 (CANL)
    Ignition switch OFF
    54 to 69 Ω
    OK
    E1-6 (CANH) - E1-14 (CANL)
    Ignition switch OFF
    69 Ω or more
    NG-A
    E1-6 (CANH) - E1-14 (CANL)
    Ignition switch OFF
    54 Ω or less
    NG-B



NG-A
CHECK CAN MAIN WIRE (FOR OPEN CIRCUIT) (Click here)

NG-B
CHECK CAN BUS WIRE (FOR SHORT CIRCUIT) (Click here)
OK


2. CHECK CAN BUS WIRE (FOR SHORT TO +B)

  1. C118856E44
    Turn the ignition switch OFF.

  1. Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E1-6 (CANH) - E1-16 (BAT)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-14 (CANL) - E1-16 (BAT)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-6 (CANH) - E1-16 (BAT)
    Ignition switch OFF
    Below 1 Ω
    NG
    E1-14 (CANL) - E1-16 (BAT)
    Ignition switch OFF
    Below 1 Ω
    NG



NG
CHECK CAN BUS WIRE (FOR SHORT TO +B) (Click here)
OK


3. CHECK CAN BUS WIRE (FOR SHORT TO GND)

  1. C118682E36
    Turn the ignition switch OFF.

  1. Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    1 Ω or more
    OK
    E1-6 (CANH) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG
    E1-14 (CANL) - E1-4 (CG)
    Ignition switch OFF
    Below 1 Ω
    NG



NG
CHECK CAN BUS WIRE (FOR SHORT TO GND) (Click here)
OK

HOW TO PROCEED WITH TROUBLESHOOTING


← Center Airbag Sensor Communication Stop Mode (from Aug 2011)CAN Bus Line (Aug 2009 – Oct 2010) →