2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built Jul 2007 – Jul 2011

Versions by build date: Jul 2007 – Jul 2011 from Aug 2011


1. INSTALL FRONT WIPER MOTOR

  1. E127869
    Install the front wiper motor.

  1. Using "Torx" socket wrench T30, tighten the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. E127871
    Apply DENSO No. 50 grease to the crank arm pivot of the front wiper motor.

  1. Install the rod onto the crank arm pivot of the front wiper motor.

  1. E127872
    Apply DENSO No. 50 grease to the crank arm pivot of the front wiper motor.

  1. Install the rod onto the crank arm pivot of the front wiper motor.


2. INSTALL FRONT WIPER MOTOR AND LINK

  1. E127873E01
    Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Connect the connector.

  1. Tighten bolt A.

  1. Tighten bolt B.

  1. Tighten 3 bolts C.

    Torque:
    7.0 N*m{ 71 kgf*cm , 61 in.*lbf }


3. INSTALL COWL TOP VENTILATOR LOUVER LH

  1. E127865
    Install the cowl top ventilator louver LH with the 5 clips and engage the 7 claws.


4. INSTALL COWL TOP VENTILATOR LOUVER RH

  1. E127864
    Install the cowl top ventilator louver RH with the 3 clips and the claw.

  1. Install the hood to cowl top seal with the clip.


5. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E127863
    Install the cowl top ventilator louver sub-assembly with the 7 clips.


6. INSTALL FRONT FENDER SIDE PANEL UPPER LH
  1. Install the 4 new clips on the front fender side panel upper LH.

  1. B210065
    Engage the 4 clips and install the front fender side panel upper LH.


7. INSTALL FRONT FENDER SIDE PANEL UPPER RH
  1. Install the 4 new clips on the front fender side panel upper RH.

  1. B210064
    Engage the 4 clips and install the front fender side panel upper RH.


8. INSTALL ANTENNA ORNAMENT

  1. E127861E02
    Press in the antenna ornament in the direction shown in the illustration.


9. INSTALL ROOF ANTENNA POLE SUB-ASSEMBLY

B138406E01
  1. Install the radio antenna pole by turning it in the direction of the arrow shown in the illustration.

    Torque:
    3.3 N*m{ 35 kgf*cm , 29 in.*lbf }

    NOTICE:
    Use a short wrench, tighten with your finger, not your hand.


10. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E127876E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


11. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (CENTER SIDE)

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E127875E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


12. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E127874E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


13. INSTALL WINDSHIELD WIPER ARM COVER

  1. E127877E01
    Engage the claw and install the 3 front wiper arm cover.

← INSPECTION (from Nov 2010)INSTALLATION (from Aug 2011) →