2011-2016 FJ Cruiser · Service Manual BODY

INSPECTION

Inspection · Vehicles built Nov 2010 – Jul 2011

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2011 from Aug 2011


INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for LHD)

  1. B135957E02
    Check the resistance.
    Text in Illustration 
    *1
    Front Passenger Switch
    *2
    Driver Switch
    *3
    Window Lock Switch
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Driver switch:
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      Always
      (ON / OFF)
      UP
      9 (B) - 3 (U)
      1 (E) - 4 (D)
      Below 1 Ω
      Always
      (ON / OFF)
      OFF
      1 (E) - 3 (U)
      1 (E) - 4 (D)
      Below 1 Ω
      Always
      (ON / OFF)
      DOWN MANUAL
      4 (D) - 9 (B)
      1 (E) - 3 (U)
      Below 1 Ω
      Always
      (ON / OFF)
      DOWN AUTO
      4 (D) - 9 (B)
      1 (E) - 3 (U)
      Below 1 Ω

      If the result is not as specified, replace the power window regulator master switch.

      Standard Resistance:
      Front passenger switch:
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      9 (B) - 8 (U)
      1 (E) - 10 (D)
      Below 1 Ω
      OFF
      OFF
      1 (E) - 8 (U)
      1 (E) - 10 (D)
      Below 1 Ω
      OFF
      DOWN
      9 (B) - 10 (D)
      1 (E) - 8 (U)
      Below 1 Ω
      ON
      UP
      9 (B) - 8 (U)
      Below 1 Ω
      ON
      UP
      1 (E) - 10 (D)
      10 kΩ or higher
      ON
      OFF
      8 (U) - 10 (D)
      Below 1 Ω
      ON
      DOWN
      9 (B) - 10 (D)
      Below 1 Ω
      ON
      DOWN
      1 (E) - 8 (U)
      10 kΩ or higher

      If the result is not as specified, replace the power window regulator master switch.

  1. Check the illumination operation.

    1. Apply battery voltage to the power window regulator master switch and check that the illumination comes on.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 9 (B)
      Battery negative (-) → Terminal 1 (E)
      Illumination comes on

      If the result is not as specified, replace the power window regulator master switch.


INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for RHD)

  1. B267114E01
    Check the resistance.
    Text in Illustration 
    *1
    Front Passenger Switch
    *2
    Driver Switch
    *3
    Window Lock Switch
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Driver switch:
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      Always
      (ON / OFF)
      UP
      15 (B) - 18 (U)
      16 (D) - 7 (E)
      Below 1 Ω
      Always
      (ON / OFF)
      OFF
      16 (D) - 7(E)
      18 (U) - 7(E)
      Below 1 Ω
      Always
      (ON / OFF)
      DOWN MANUAL
      15 (B) - 16 (D)
      7 (E) - 18 (U)
      Below 1 Ω
      Always
      (ON / OFF)
      DOWN AUTO
      15 (B) - 16 (D)
      7 (E) - 18 (U)
      Below 1 Ω

      If the result is not as specified, replace the power window regulator master switch.

      Standard Resistance:
      Front passenger switch:
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      12 (U) - 15 (B)
      7 (E) - 10 (D)
      Below 1 Ω
      OFF
      OFF
      7 (E) - 12 (U)
      7 (E) - 10 (D)
      Below 1 Ω
      OFF
      DOWN
      10 (D) - 15 (B)
      7 (E) - 12 (U)
      Below 1 Ω
      ON
      UP
      12 (U) - 15 (B)
      Below 1 Ω
      ON
      OFF
      10 (D) - 12 (U)
      Below 1 Ω
      ON
      DOWN
      10 (D) - 15 (B)
      Below 1 Ω

      If the result is not as specified, replace the power window regulator master switch.

  1. Check the illumination operation.

    1. Apply battery voltage to the power window regulator master switch and check that the illumination comes on.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 15 (B)
      Battery negative (-) → Terminal 7 (E)
      Illumination comes on

      If the result is not as specified, replace the power window regulator master switch.

← INSPECTION (Jul 2007 – Oct 2010)INSPECTION (from Aug 2011) →