2011-2016 FJ Cruiser · Service Manual BODY

INSPECTION

Inspection · Vehicles built from Aug 2011

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2011 from Aug 2011


INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for LHD)

  1. E148358E01
    Check the resistance.
    Text in Illustration 
    *1
    Window Lock Switch
    *2
    Driver Switch
    *3
    Front Passenger Switch
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Driver switch:
      Tester Connection
      Window Lock Switch Condition
      Power Window Switch Condition
      Specified Condition
      10 (U) - 15 (B)
      Always
      (ON / OFF)
      UP
      10 kΩ or higher
      7 (E) - 12 (D)
      Always
      (ON / OFF)
      UP
      Below 1 Ω
      7(E) - 12 (D)
      7(E) - 10 (U)
      Always
      (ON / OFF)
      OFF
      Below 1 Ω
      12 (D) - 15 (B)
      Always
      (ON / OFF)
      DOWN MANUAL
      10 kΩ or higher
      7 (E) - 10 (U)
      Always
      (ON / OFF)
      DOWN MANUAL
      Below 1 Ω
      12 (D) - 15 (B)
      Always
      (ON / OFF)
      DOWN AUTO
      10 kΩ or higher
      7 (E) - 10 (U)
      Always
      (ON / OFF)
      DOWN AUTO
      Below 1 Ω

      If the result is not as specified, replace the power window regulator master switch assembly.

      Standard Resistance:
      Front passenger switch:
      Tester Connection
      Window Lock Switch Condition
      Power Window Switch Condition
      Specified Condition
      15 (B) - 16 (U)
      7 (E) - 18 (D)
      OFF
      UP
      Below 1 Ω
      7 (E) - 16 (U)
      7 (E) - 18 (D)
      OFF
      OFF
      Below 1 Ω
      15 (B) - 18 (D)
      7 (E) - 16 (U)
      OFF
      DOWN
      Below 1 Ω
      15 (B) - 16 (U)
      ON
      UP
      Below 1 Ω
      16 (U) - 18 (D)
      ON
      OFF
      Below 1 Ω
      15 (B) - 18 (D)
      ON
      DOWN
      Below 1 Ω

      If the result is not as specified, replace the power window regulator master switch assembly.

  1. Check the illumination operation.

    1. Apply battery voltage to the power window regulator master switch and check that the illumination comes on.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 15 (B)
      Battery negative (-) → Terminal 7 (E)
      Illumination comes on

      If the result is not as specified, replace the power window regulator master switch assembly.


INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for RHD)

  1. B267114E01
    Check the resistance.
    Text in Illustration 
    *1
    Front Passenger Switch
    *2
    Driver Switch
    *3
    Window Lock Switch
    *a
    Component without harness connected
    (Power Window Regulator Master Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Driver switch:
      Tester Connection
      Window Lock Switch Condition
      Power Window Switch Condition
      Specified Condition
      15 (B) - 18 (U)
      Always
      (ON / OFF)
      UP
      10 kΩ or higher
      16 (D) - 7 (E)
      Always
      (ON / OFF)
      UP
      Below 1 Ω
      16 (D) - 7(E)
      18 (U) - 7(E)
      Always
      (ON / OFF)
      OFF
      Below 1 Ω
      15 (B) - 16 (D)
      Always
      (ON / OFF)
      DOWN MANUAL
      10 kΩ or higher
      7 (E) - 18 (U)
      Always
      (ON / OFF)
      DOWN MANUAL
      Below 1 Ω
      15 (B) - 16 (D)
      Always
      (ON / OFF)
      DOWN AUTO
      10 kΩ or higher
      7 (E) - 18 (U)
      Always
      (ON / OFF)
      DOWN AUTO
      Below 1 Ω

      If the result is not as specified, replace the power window regulator master switch assembly.

      Standard Resistance:
      Front passenger switch:
      Tester Connection
      Window Lock Switch Condition
      Power Window Switch Condition
      Specified Condition
      12 (U) - 15 (B)
      7 (E) - 10 (D)
      OFF
      UP
      Below 1 Ω
      7 (E) - 12 (U)
      7 (E) - 10 (D)
      OFF
      OFF
      Below 1 Ω
      10 (D) - 15 (B)
      7 (E) - 12 (U)
      OFF
      DOWN
      Below 1 Ω
      12 (U) - 15 (B)
      ON
      UP
      Below 1 Ω
      10 (D) - 12 (U)
      ON
      OFF
      Below 1 Ω
      10 (D) - 15 (B)
      ON
      DOWN
      Below 1 Ω

      If the result is not as specified, replace the power window regulator master switch assembly.

  1. Check the illumination operation.

    1. Apply battery voltage to the power window regulator master switch and check that the illumination comes on.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 15 (B)
      Battery negative (-) → Terminal 7 (E)
      Illumination comes on

      If the result is not as specified, replace the power window regulator master switch assembly.

← INSPECTION (Nov 2010 – Jul 2011)INSTALLATION (from Jul 2007) →