2011-2016 FJ Cruiser · Service Manual BRAKE

TERMINALS OF ECU

System information · Vehicles built Jul 2007 – Jul 2008

Versions by build date: Jul 2007 – Jul 2008 Aug 2008 – Oct 2010 from Nov 2010


TERMINALS OF ECU
C110610E06
Symbols (Terminal No.)
Terminal Description
GND1 (1)
Skid control ECU ground
+BM1 (2)
Power supply for motor
FR+ (3)
Front right wheel speed sensor power supply output
FL- (4)
Front left wheel speed signal input
RR+ (5)
Rear right wheel speed sensor power supply output
RL- (6)
Rear left wheel speed signal input
STP (7)
Stop light switch input
NEO (10) (*1)
2WD/4WD change over switch input
CANH (11)
CAN communication line H
SP1 (12) (*1)
Speed signal output for combination meter
D/G (13)
Diagnosis tester communication line
P (14) (*1)
Shift position indicator P signal input
STPO (16)
Stop light operated relay output
FR- (17)
Front right wheel speed sensor input
FL+ (18)
Front left wheel speed sensor power supply output
RR- (19)
Rear right wheel speed sensor input
RL+ (20)
Rear left wheel speed sensor power supply output
EXI4 (21)
Transfer indicator switch (L4) input
TS (24)
Sensor test terminal (Sensor check switch) input
CANL (25)
CAN communication line L
EXI3 (26) (*2)
Rear differential lock position switch input
EXI (27)
Transfer indicator switch (A/T: 4WD position, M/T: center differential lock position) input
PKB (28)
Parking brake switch input
WA (29)
ABS warning light input
BZ (30)
Skid control buzzer output
+BS (31)
Power supply for solenoid
GND2 (32)
Skid control ECU ground
HDCW (33) (*3)
A-TRAC indicator light output
IND (34)
SLIP indicator light output
WT (35)
VSC OFF indicator light output
VSCW (36)
VSC TRC warning light output
LBL (41)
Brake fluid level warning switch input
WFSE (42)
Write flash enable input
HDCS (44) (*3)
A-TRAC switch input
STP2 (45)
Stop light switch input
IG1 (46)
IG1 power supply
C124763E03
Symbols (Terminal No.)
Terminal Description
IG2 (1)
IG2 power supply
+BM2 (2)
Power supply for motor
BRL (3)
BRAKE warning light output
GND3 (4)
Skid control ECU ground
  1. (*1): A/T
  2. (*2): with rear differential lock
  3. (*3): with A-TRAC

TERMINAL INSPECTION
Disconnect the connector and measure the voltage or resistance on the wire harness side.

HINT:
Voltage cannot be measured with the connector connected to the skid control ECU as the connector is water resistant.

C124764E03
Standard 
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
+BM1 (A4-2) - GND1, GND2 (A4-1, 32)
L-Y - W-B
Power supply for motor from battery
Always
11 to 14 V
IG1 (A4-46) - GND1, GND2 (A4-1, 32)
B-R - W-B
IG1 power supply
IG switch OFF
Below 1 V
IG1 (A4-46) - GND1, GND2 (A4-1, 32)
B-R - W-B
IG1 power supply
IG switch ON
11 to 14 V
STP (A4-7) - GND1, GND2 (A4-1, 32)
G-B - W-B
Stop light switch input
Stop light switch OFF (Brake pedal released)
Below 1.5 V
STP (A4-7) - GND1, GND2 (A4-1, 32)
G-B - W-B
Stop light switch input
Stop light switch ON (Brake pedal released)
8 to 14 V
P (A4-14) - GND1, GND2 (A4-1, 32) (*1)
Y-B - W-B
Shift position indicator P signal input
IG switch ON, shift P position
8 to 14 V
P (A4-14) - GND1, GND2 (A4-1, 32) (*1)
Y-B - W-B
Shift position indicator P signal input
IG switch ON, any shift position except P
Below 1 V
EXI4 (A4-21) - GND1, GND2 (A4-1, 32) (*1)
W-L - W-B
Transfer indicator switch (L4) input
IG switch ON, transfer position L4
Below 1.5 V
EXI4 (A4-21) - GND1, GND2 (A4-1, 32) (*1)
W-L - W-B
Transfer indicator switch (L4) input
IG switch ON, transfer condition except L4
8 to 14 V
EXI3 (A4-26) - GND1, GND2 (A4-1, 32) (*2)
L-Y - W-B
Rear differential lock detection switch input
IG switch ON, rear differential lock switch ON
Below 1.5 V
EXI3 (A4-26) - GND1, GND2 (A4-1, 32) (*2)
L-Y - W-B
Rear differential lock detection switch input
IG switch ON, rear differential lock switch OFF
8 to 14 V
EXI (A4-27) - GND1, GND2 (A4-1, 32)
GR - W-B
Transfer indicator switch (A/T: 4WD position, M/T: center differential lock position) input
A/T: IG switch ON, transfer condition H4 or L4
M/T: IG switch ON, transfer condition LL or HL
Below 1.5 V
EXI (A4-27) - GND1, GND2 (A4-1, 32)
GR - W-B
Transfer indicator switch (A/T: 4WD position, M/T: center differential lock position) input
A/T: IG switch ON, transfer condition H2
M/T: IG switch ON, transfer condition H
8 to 14 V
PKB (A4-28) - GND1, GND2 (A4-1, 32)
W-R - W-B
Parking brake switch input
IG switch ON, parking brake switch ON
Below 1.5 V
PKB (A4-28) - GND1 , GND2 (A4-1, 32)
W-R - W-B
Parking brake switch input
IG switch ON, parking brake switch OFF
11 to 14 V
+BS (A4-31) - GND1, GND2 (A4-1, 32)
Y - W-B
Power supply for solenoid from battery
Always
11 to 14 V
LBL (A4-41) - GND1, GND2 (A4-1, 32)
V-R - W-B
Brake fluid level warning switch input
Brake fluid level min. -5mm
Below 1 Ω
LBL (A4-41) - GND1, GND2 (A4-1, 32)
V-R - W-B
Brake fluid level warning switch input
Brake fluid level max.
1.9 k to 2.1 kΩ
HDCS (A4-44) - GND1, GND2 (A4-1, 32) (*3)
P-G - W-B
A-TRAC switch input
Ignition switch ON, A-TRAC switch ON
Below 1.5 V
HDCS (A4-44) - GND1, GND2 (A4-1, 32) (*3)
P-G - W-B
A-TRAC switch input
Ignition switch ON, A-TRAC switch OFF
8 to 14 V
STP2 (A4-45) - GND1, GND2 (A4-1, 32)
G-Y - W-B
Stop light switch input
Stop light switch OFF (Brake pedal released)
Below 1.5 V
STP2 (A4-45) - GND1, GND2 (A4-1, 32)
G-Y - W-B
Stop light switch input
Stop light switch ON (Brake pedal released)
8 to 14 V
IG2 (A5-1) - GND3 (A5-4)
B-O - W-B
IG2 power supply
IG switch OFF
Below 1 V
IG2 (A5-1) - GND3 (A5-4)
B-O - W-B
IG2 power supply
IG switch ON
11 to 14 V
+BM2 (A5-2) - GND3 (A5-4)
L-Y - W-B
Power supply for motor from battery
Always
11 to 14 V

HINT:
  1. (*1): A/T
  2. (*2): with rear differential lock
  3. (*3): with A-TRAC

← PROBLEM SYMPTOMS TABLE (from Aug 2014)TERMINALS OF ECU (Aug 2008 – Oct 2010) →