TERMINALS OF ECU
System information · Vehicles built Aug 2008 – Oct 2010
Versions by build date: Jul 2007 – Jul 2008 Aug 2008 – Oct 2010 from Nov 2010
| TERMINALS OF ECU |


| Symbols (Terminal No.) |
Terminal Description |
| GND1 (1) |
Skid control ECU ground |
| +BM1 (2) |
Power supply for motor |
| FR+ (3) |
Front right wheel speed sensor power supply output |
| FL- (4) |
Front left wheel speed signal input |
| RR+ (5) |
Rear right wheel speed sensor power supply output |
| RL- (6) |
Rear left wheel speed signal input |
| STP (7) |
Stop light switch input |
| NEO (10) (*1) |
2WD/4WD changeover switch input |
| CANH (11) |
CAN communication line H |
| SP1 (12) (*1) |
Speed signal output for combination meter |
| D/G (13) |
Diagnosis tester communication line |
| P (14) (*1) |
Shift position indicator P signal input |
| STPO (16) |
Stop light operated relay output |
| FR- (17) |
Front right wheel speed sensor input |
| FL+ (18) |
Front left wheel speed sensor power supply output |
| RR- (19) |
Rear right wheel speed sensor input |
| RL+ (20) |
Rear left wheel speed sensor power supply output |
| EXI4 (21) (*4) |
Transfer indicator switch (A/T: 4WD position, M/T: center differential lock position) input |
| EXI4 (21) (*5) |
Transfer indicator switch (L4) input |
| TS (24) |
Sensor test terminal (Sensor check switch) input |
| CANL (25) |
CAN communication line L |
| EXI3 (26) (*2) |
Rear differential lock position switch input |
| EXI (27) (*4) |
Transfer indicator switch (L4) input |
| EXI (27) (*5) |
Transfer indicator switch (A/T: 4WD position, M/T: center differential lock position) input |
| PKB (28) |
Parking brake switch input |
| WA (29) |
ABS warning light input |
| BZ (30) |
Skid control buzzer output |
| +BS (31) |
Power supply for solenoid |
| GND2 (32) |
Skid control ECU ground |
| HDCW (33) (*3) |
A-TRAC indicator light output |
| IND (34) |
SLIP indicator light output |
| WT (35) |
VSC OFF indicator light output |
| VSCW (36) |
TRC OFF indicator light output (*4) VSC TRC warning light output (*5) |
| LBL (41) |
Brake fluid level warning switch input |
| WFSE (42) |
Write flash enable input |
| CSW (43) |
VSC OFF switch input |
| HDCS (44) (*3) |
A-TRAC switch input |
| STP2 (45) |
Stop light switch input |
| IG1 (46) |
IG1 power supply |
- HINT:
- *1: Automatic transmission
- *2: w/ rear differential lock
- *3: w/ A-TRAC
- *4: w/ VSC OFF Switch
- *5: w/o VSC OFF Switch


| Symbols (Terminal No.) |
Terminal Description |
| IG2 (1) |
IG2 power supply |
| +BM2 (2) |
Power supply for motor |
| BRL (3) |
BRAKE warning light output |
| GND3 (4) |
Skid control ECU ground |
| TERMINAL INSPECTION |
- HINT:
- Voltage cannot be measured with the connector connected to the skid control ECU as the connector is water resistant.


| Symbols (Terminal No.) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| +BM1 (A4-2) - GND1, GND2 (A4-1, 32) |
L-Y - W-B |
Power supply for motor from battery |
Always |
11 to 14 V |
| IG1 (A4-46) - GND1, GND2 (A4-1, 32) |
B-R - W-B |
IG1 power supply |
IG switch OFF |
Below 1 V |
| IG1 (A4-46) - GND1, GND2 (A4-1, 32) |
B-R - W-B |
IG1 power supply |
IG switch ON |
11 to 14 V |
| STP (A4-7) - GND1, GND2 (A4-1, 32) |
G-B - W-B |
Stop light switch input |
Stop light switch OFF (Brake pedal released) |
Below 1.5 V |
| STP (A4-7) - GND1, GND2 (A4-1, 32) |
G-B - W-B |
Stop light switch input |
Stop light switch ON (Brake pedal released) |
8 to 14 V |
| P (A4-14) - GND1, GND2 (A4-1, 32) (*1) |
Y-B - W-B |
Shift position indicator P signal input |
IG switch ON, shift P position |
8 to 14 V |
| P (A4-14) - GND1, GND2 (A4-1, 32) (*1) |
Y-B - W-B |
Shift position indicator P signal input |
IG switch ON, any shift position except P |
Below 1 V |
| EXI4 (A4-21) (*4) - GND1, GND2 (A4-1, 32) |
GR - W-B |
Transfer indicator switch (A/T: 4WD position, M/T: center differential lock position) input |
A/T: IG switch ON, transfer condition H4 or L4 M/T: IG switch ON, transfer condition LL or HL |
Below 1.5 V |
| EXI4 (A4-21) (*4) - GND1, GND2 (A4-1, 32) |
GR - W-B |
Transfer indicator switch (A/T: 4WD position, M/T: center differential lock position) input |
A/T: IG switch ON, transfer condition H2 M/T: IG switch ON, transfer condition H |
8 to 14 V |
| EXI4 (A4-21) (*5) - GND1, GND2 (A4-1, 32) (*1) |
W-L - W-B |
Transfer indicator switch (L4) input |
IG switch ON, transfer position L4 |
Below 1.5 V |
| EXI4 (A4-21) (*5) - GND1, GND2 (A4-1, 32) (*1) |
W-L - W-B |
Transfer indicator switch (L4) input |
IG switch ON, transfer condition except L4 |
8 to 14 V |
| EXI3 (A4-26) - GND1, GND2 (A4-1, 32) (*2) |
L-Y - W-B |
Rear differential lock detection switch input |
IG switch ON, rear differential lock switch ON |
Below 1.5 V |
| EXI3 (A4-26) - GND1, GND2 (A4-1, 32) (*2) |
L-Y - W-B |
Rear differential lock detection switch input |
IG switch ON, rear differential lock switch OFF |
8 to 14 V |
| EXI (A4-27) (*4) - GND1, GND2 (A4-1, 32) |
W-L - W-B |
Transfer indicator switch (L4) input |
IG switch ON, transfer position L4 |
Below 1.5 V |
| EXI (A4-27) (*4) - GND1, GND2 (A4-1, 32) |
W-L - W-B |
Transfer indicator switch (L4) input |
IG switch ON, transfer condition except L4 |
8 to 14 V |
| EXI (A4-27) (*5) - GND1, GND2 (A4-1, 32) |
GR - W-B |
Transfer indicator switch (A/T: 4WD position, M/T: center differential lock position) input |
A/T: IG switch ON, transfer condition H4 or L4 M/T: IG switch ON, transfer condition LL or HL |
Below 1.5 V |
| EXI (A4-27) (*5) - GND1, GND2 (A4-1, 32) |
GR - W-B |
Transfer indicator switch (A/T: 4WD position, M/T: center differential lock position) input |
A/T: IG switch ON, transfer condition H2 M/T: IG switch ON, transfer condition H |
8 to 14 V |
| PKB (A4-28) - GND1, GND2 (A4-1, 32) |
W-R - W-B |
Parking brake switch input |
IG switch ON, parking brake switch ON |
Below 1.5 V |
| PKB (A4-28) - GND1 , GND2 (A4-1, 32) |
W-R - W-B |
Parking brake switch input |
IG switch ON, parking brake switch OFF |
11 to 14 V |
| +BS (A4-31) - GND1, GND2 (A4-1, 32) |
Y - W-B |
Power supply for solenoid from battery |
Always |
11 to 14 V |
| LBL (A4-41) - GND1, GND2 (A4-1, 32) |
V-R - W-B |
Brake fluid level warning switch input |
Brake fluid level min. -5 mm |
Below 1 Ω |
| LBL (A4-41) - GND1, GND2 (A4-1, 32) |
V-R - W-B |
Brake fluid level warning switch input |
Brake fluid level max. |
1.9 k to 2.1 kΩ |
| HDCS (A4-44) - GND1, GND2 (A4-1, 32) (*3) |
P-G - W-B |
A-TRAC switch input |
Ignition switch ON, A-TRAC switch ON |
Below 1.5 V |
| HDCS (A4-44) - GND1, GND2 (A4-1, 32) (*3) |
P-G - W-B |
A-TRAC switch input |
Ignition switch ON, A-TRAC switch OFF |
8 to 14 V |
| STP2 (A4-45) - GND1, GND2 (A4-1, 32) |
G-Y - W-B |
Stop light switch input |
Stop light switch OFF (Brake pedal released) |
Below 1.5 V |
| STP2 (A4-45) - GND1, GND2 (A4-1, 32) |
G-Y - W-B |
Stop light switch input |
Stop light switch ON (Brake pedal released) |
8 to 14 V |
| IG2 (A5-1) - GND3 (A5-4) |
B-O - W-B |
IG2 power supply |
Ignition switch OFF |
Below 1 V |
| IG2 (A5-1) - GND3 (A5-4) |
B-O - W-B |
IG2 power supply |
Ignition switch ON |
11 to 14 V |
| +BM2 (A5-2) - GND3 (A5-4) |
L-Y - W-B |
Power supply for motor from battery |
Always |
11 to 14 V |
- HINT:
- *1: Automatic transmission
- *2: w/ rear differential lock
- *3: w/ A-TRAC
- *4: w/ VSC OFF Switch
- *5: w/o VSC OFF Switch
- *1: Automatic transmission