2011-2016 FJ Cruiser · Service Manual BRAKE

C1253/53 Pump Motor Relay Malfunction

Diagnostic trouble codes · Vehicles built Jul 2007 – Oct 2010

DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU.
DTC No.
DTC Detecting Condition
Trouble Areas
C1253/53
Open in motor system circuit (motor input circuit)
  1. ABS MTR fuse
  2. +BM terminal circuit
  3. Hydraulic brake booster

WIRING DIAGRAM

C164953E01

INSPECTION PROCEDURE

NOTICE:
When replacing the hydraulic brake booster, perform zero point calibration (Click here).


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)
  1. Connect an intelligent tester to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Select the following menu items: Chassis / ABS/VSC/TRC/ Active TestSelect the "ABS Motor Relay" in the Active Test and operate the actuator motor using the intelligent tester.

    ACTIVE TEST: ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ABS Motor Relay
    ABS motor relay
    ABS motor relay ON or OFF
    Operation of motor can be heard

  1. Check for operation sound of the actuator motor when it is operated with the intelligent tester.

    OK:
    The operation sound of the actuator motor can be heard.



NG
Go to step 3
OK


2. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off

  1. Depress the brake pedal more than 20 times.

  1. Turn the ignition switch to ON.

  1. Wait until the pump motor stops.

  1. Depress the brake pedal several times until the pump motor is turned on.

  1. Wait until the pump stops.

  1. Repeat (f) and (g) three times.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE HYDRAULIC BRAKE BOOSTER (Click here)

3. INSPECT FUSE (ABS MTR)

  1. C139129E01
    Remove the ABS MTR fuse from the engine room R/B No. 2.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


4. INSPECT SKID CONTROL ECU TERMINAL VOLTAGE (+BM, +BM2 TERMINAL)

  1. C124799E11
    Disconnect the skid control ECU connectors.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Specified Condition
    A4-2 (+BM1) - Body ground
    11 to 14 V
    A5-2 (+BM2) - Body ground
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM1 AND +BM2 CIRCUIT)
OK


5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BODY GROUND)

  1. C124799E03
    Disconnect the skid control ECU connectors.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    A4-1 (GND1) - Body ground
    Below 1 Ω
    A4-32 (GND2) - Body ground
    Below 1 Ω
    A5-4 (GND3) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


6. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Depress the brake pedal more than 20 times.

  1. Turn the ignition switch to ON.

  1. Wait until the pump motor stops.

  1. Depress the brake pedal several times until the pump motor is turned on.

  1. Wait until the pump stops.

  1. Repeat (f) and (g) three times.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE HYDRAULIC BRAKE BOOSTER (Click here)


← C1253 Pump Motor Relay (from Aug 2012)C1254 Pressure Sensor or Switch (Nov 2010 – Jul 2012) →