2011-2016 FJ Cruiser · Service Manual BRAKE

C1241 Low Power Supply Voltage Malfunction

Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2011

Versions by build date: Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012

DESCRIPTION

If there is a problem with the master cylinder solenoid (skid control ECU) power supply circuit, the skid control ECU outputs the DTC and prohibits operation under the fail-safe function.
If the voltage supplied to terminal IG1 is not within the DTC detection threshold due to malfunctions in parts such as the battery and generator circuit, this DTC is stored.
DTC Code
DTC Detection Condition
Trouble Area
C1241
When either of following conditions detected:
1. Both of following conditions continue for at least 10 seconds.
  1. Vehicle speed more than 3 km/h (2 mph).
  2. IG1 terminal voltage less than 9.5 V.
2. All of following conditions continue for at least 0.2 seconds.
  1. Solenoid relay remains ON.
  2. IG1 terminal voltage less than 9.5 V.
  3. Relay contact open.
  1. Battery
  2. ECU-IG fuse
  3. Charging system
  4. Harness or connector
  5. Master cylinder solenoid (skid control ECU)

WIRING DIAGRAM

C230319E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. READ VALUE USING INTELLIGENT TESTER (IG VOLTAGE)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item : Range
    Normal Condition
    Diagnostic Note
    IG1 Voltage Value
    IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V
    11 to 14 V
    Changes in proportion to battery voltage

  1. Measure the voltage output from the ECU displayed on the tester.

    Result 
    Result
    Proceed
    Data display is within Normal Condition
    A
    Data display is not within Normal Condition
    B



B
Go to step 3
A


2. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTCs are output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output (When troubleshooting in accordance with Diagnostic Trouble Code Chart)
    B
    DTC is not output (When troubleshooting in accordance with Problem Symptoms Table)
    C



B
USE SIMULATION METHOD TO CHECK (Click here)

C
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)

3. INSPECT SKID CONTROL ECU (IG1 TERMINAL)

  1. C214161E51
    Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-46 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT SKID CONTROL ECU (GND TERMINAL)

  1. C124799E53
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A4-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A5-4 (GND3) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTCs are output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output (When troubleshooting in accordance with Diagnostic Trouble Code Chart)
    B
    DTC is not output (When troubleshooting in accordance with Problem Symptoms Table)
    C



B
USE SIMULATION METHOD TO CHECK (Click here)

C
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)


← C1240 Yaw Rate Sensor Discrimination (from Aug 2012)C1241 Low Power Supply Voltage Malfunction (Aug 2011 – Jul 2012) →